Skip to content
Cart1

InstaPanel vs Fibre Cement Cladding: Supply & Install Cost Compared (2026)

InstaPanel cladding

InstaPanel vs fibre cement cladding · supply & install

Save about $45 per m² on day one, and about $165 per m² over 25 years

Short answer: on a typical 50 m² wall, InstaPanel by Devox costs about $118 per m² supplied and installed, against about $163 per m² for Hardie™ Fine Texture and $172 per m² for Axon™ 133 Smooth once priming and painting are included. That is a saving of roughly $45 per m² on day one. Fibre cement then needs repainting every 7–10 years and InstaPanel never needs painting, so over 25 years the gap grows to about $165 per m² (estimate). InstaPanel is also lighter and faster to install, with fewer headaches from cracks and leaks. This guide compares the two on cost, installation, compliance and upkeep.

$118/m²
InstaPanel, all-in supply & install (50 m² example)
$165/m²
Saved over 25 years vs Fine Texture once repaints are counted (estimate)
3.7 kg/m²
InstaPanel weight. Fine Texture is 13.1 kg/m², Axon™ 13 kg/m²
~2 days
On site for 50 m² of InstaPanel vs ~4 days for fibre cement plus paint

Key takeaways

  • ✔Cheaper to finish: about $118/m² supplied and installed, against $163/m² (Fine Texture) and $172/m² (Axon™ 133) on a 50 m² wall.
  • ✔Never painted: no primer, no top coats and no repaint every 7–10 years. Over 25 years that is about $165/m² saved against Fine Texture (estimate).
  • ✔Faster and lighter: about 2 days on site for 50 m² vs about 4, and 3.7 kg/m² vs about 13 kg/m².
  • ✔Fewer headaches: interlocking, sealed joints and no paint film to crack, peel or let water in.
  • ✔Know the limits: keep InstaPanel 900mm from a boundary and 1800mm from another building, not for fire-rated (FRL) walls; check bushfire requirements with your certifier.

All prices are indicative, in AUD including GST, as at November 2026. Every job is different, so ask us for a written quote.

Mockup: InstaPanel White on a box-form double-storey home with dark brick and a timber garage
InstaPanel by Devox, installed
1 · The products

What are you comparing?

InstaPanel (Devox)

InstaPanel is a 16mm insulated wall cladding panel from Devox. It has a pre-finished aluminium-zinc coated steel face, a rigid polyurethane (PU) foam core and an aluminium foil backing. The panels are 383mm wide, weigh 3.7 kg/m² and come in Grey 801 or White 802. Alpha Timber stocks 2.7m, 3.0m and 5.8m lengths.

Hardie™ Fine Texture & Axon™ 133

Hardie™ Fine Texture Cladding and Axon™ Cladding 133mm Smooth are 1200mm-wide fibre cement sheets made by James Hardie. Fine Texture is 8.5mm thick with a fine render-look texture. Axon™ is 9mm thick with vertical grooves every 133mm that give a painted VJ timber look. Both arrive pre-sealed only, so they need a primer and two top coats of paint on site.

2 · At a glance

Side-by-side comparison

InstaPanel (Devox) Hardie™ Fine Texture Axon™ 133 Smooth
Thickness 16mm 8.5mm 9mm
Weight 3.7 kg/m² 13.1 kg/m² 13 kg/m²
Sizes 383mm × 2.7, 3.0, 5.8m 1200mm × 2440–3600mm 1200mm × 2450–3600mm
Material price, incl. 10% waste* ~$34/m² ~$50/m² ~$56–61/m²
Finish ✔ Pre-finished, never needs painting Pre-sealed only: primer + 2 coats on site, repaint every 7–10 years Pre-sealed only: primer + 2 coats on site, repaint every 7–10 years
Insulation ✔ 16mm PU core, typically about R0.44–R0.65 for this panel type About R0.03 About R0.04
Fire Non-combustible steel face over an enclosed PU core; for walls 900mm+ from a boundary; not for fire-rated (FRL) walls Non-combustible, BAL-40 Non-combustible, BAL-40
Boundary limits Not within 900mm of a boundary or 1800mm of another building Can be used in tested Hardie™ boundary and fire-rated systems Check James Hardie fire-rated system guides
Termites and rot ✔ Not termite food: steel is termite-resistant (CSIRO) and termites don't eat PU foam Resistant (James Hardie) Resistant (James Hardie)
Cutting ✔ Angle grinder or circular saw Silica dust controls required Silica dust controls required
Warranty 20 years; can last up to 25 years 25 years (James Hardie) 25 years (James Hardie)

*Alpha Timber retail per m² of wall face plus up to 10% waste, November 2026. InstaPanel is $32.40 (2.7m), $36.00 (3.0m) or $69.60 (5.8m) per panel. Hardie™ Fine Texture is $133.31–$196.37 per sheet and Axon™ Cladding is $156.00–$237.00 per sheet.

InstaPanel by Devox, installed
3 · Worked example

Supply and install: what a 50 m² wall really costs

Comparing sheet prices alone can mislead. A finished wall also needs wall wrap, trims and flashings, fixings, labour and, for fibre cement, paint. The Devox installation guide recommends fixing InstaPanel to battens rather than straight to the studs (unless your engineer approves direct fixing), so we've included a batten cavity for InstaPanel too.

The example is a single-storey extension: 50 m² of wall, 2.7m high, 18.5m long with two external corners, on a new timber frame with easy access.

50 m² wall InstaPanel Fine Texture Axon™ 133
Panels/sheets (incl. 10% waste) $1,728 $2,542 $2,861
Wall wrap $134 $134 $134
Trims and flashings (incl. 10% waste) $1,011 $595 $708
Fixings and sealant $150 $150 $150
Cavity battens, installed $1,125 — —
Install labour $1,750 $3,000 $3,000
Painting: primer + 2 coats — $1,750 $1,750
Total $5,898 $8,171 $8,603
Per m² $118 $163 $172

✔ InstaPanel saves $2,273 against Fine Texture and $2,705 against Axon™ on 50 m². On a 100 m² wall the pattern holds: about $11,800 for InstaPanel, $16,400 for Fine Texture and $17,300 for Axon™, a saving of about $4,500 against Fine Texture.

4 · Cost over time

Over 25 years: the painting bill fibre cement keeps adding

Fibre cement has to be repainted every 7–10 years to stay protected. Sydney exterior painting typically costs $25–$60 per m² of wall, around $40 on average. Using an estimated $40/m² for repaints at years 8, 16 and 24, the 25-year cost per m² looks like this:

25 years, per m² (estimate) InstaPanel Fine Texture Axon™ 133
Supplied & installed $118 $163 $172
3 repaints at ~$40/m² $0, never painted $120 $120
25-year total $118 $283 $292

25-year total per m² (estimate)

InstaPanel
$118/m²
Hardie™ Fine Texture
$283/m²
Axon™ 133
$292/m²

✔ On a 50 m² wall that's about $8,270 saved against Fine Texture and $8,700 against Axon™ over 25 years, in today's dollars and before scaffold for two-storey repaints.

Ready to price your wall in InstaPanel?

Send us your plans or wall sizes for an itemised quote.

How we worked it out

Material and trim prices are Alpha Timber retail, with up to 10% added for waste on panels, sheets, wall wrap and trim lengths. Install labour is an indicative $35/m² for InstaPanel and $60/m² for fibre cement; published Australian guides put fibre cement installation at $30–$70/m². Painting is an estimated $35/m² for a primer plus two top coats, the top of the $20–$35/m² range Yakka Labour gives for priming and two coats on new cladding. Battens are $22.50/m², the middle of the $15–$30/m² installed range. InstaPanel trims aren't listed separately online, so we priced them at the same rates as aluminium trims, which is a conservative estimate. Scaffolding, removing old cladding, delivery and approvals are extra.

Mockup: InstaPanel White on a curved-bay double-storey home
InstaPanel by Devox, installed
5 · Faster to finish

Installation and time on site

InstaPanel by Devox installed on an upper-storey wall
InstaPanel by Devox, installed

InstaPanel

InstaPanel can go on horizontally or vertically. For horizontal runs, a starter channel is screwed at the base, then each panel's groove interlocks over the tongue of the panel below, with screws through the tongue at no more than 450mm centres. A closing kit and cap finish the top, and every exposed edge is trimmed so the foam core is never open to water. Studs must be at 450mm centres or less. A panel weighs 4–8 kg, so one person can handle it, and there's no painter to book afterwards.

Fine Texture and Axon™

Sheets are fixed vertically with shiplap joints, gun nailed with stainless brad nails, and finished with base and corner trims. They can be direct fixed to a timber frame or cavity fixed on battens. Sheets weigh roughly 38–57 kg, so it's usually a two-person lift. Because they arrive pre-sealed only, they then need a primer and two coats of exterior acrylic paint. For Fine Texture, James Hardie says this must be done within three months of fixing, or straight away within 1km of the coast.

Time on site (estimate)

As a rough guide, a two-person crew can clad 50 m² with InstaPanel in about two days including battens, with nothing to paint. Fibre cement takes about four days once painting and drying time are included. These are estimates; weather, access and detail work change the timing.

6 · Compliance

Fire, bushfire and boundary rules

This is the most important part of the decision.

For most extensions, granny flats, sheds, carports and feature walls on clear sites, InstaPanel fits easily. If your wall is near a boundary, in a bushfire-prone area or needs an FRL, talk to us and your certifier first; fibre cement in a tested system may be needed there.

InstaPanel

InstaPanel has a non-combustible steel face that won't burn or carry flame, over a PU foam core that is fully enclosed by the steel, the foil backing and trims. PU foam itself is combustible, and there's no published AS 1530.1 test for the whole panel, so it isn't classed as a non-combustible material under the NCC. For most houses that doesn't matter: the NCC Housing Provisions only require fire-rated external walls within 900mm of a boundary or 1.8m of another building, and those are exactly Devox's limits: it must not be installed less than 900mm from an allotment boundary or 1800mm from another building, as defined in the National Construction Code, and it isn't for walls that need a fire-resistance level (FRL). No BAL rating is published, but at BAL-12.5 and BAL-19, AS 3959 sets no material rule for wall parts 400mm or more above the ground, decks or low roofs (your certifier confirms).

Hardie™ Fine Texture and Axon™

These are fibre cement, which James Hardie states is suitable where non-combustible materials are required (NCC C2D10). Both are listed to BAL-40, and Fine Texture can form part of James Hardie's fire-rated and boundary-wall systems.

7 · Comfort

Insulation, weight and handling

Built-in insulation

InstaPanel's PU foam core adds a layer of insulation and helps reduce outside noise. Fibre cement sheets don't have this. Makers of the same panel type (16mm PU core with a steel face and foil back) publish thermal resistance of about R0.44–R0.65, and US insulated siding is certified at R-2 to R-3 imperial (about R0.35–R0.53 metric). Fibre cement sheet is about R0.03–R0.04 (NCC value 0.25 W/m·K). These are typical figures for this kind of panel, not Devox test results, so treat it as a bonus rather than a replacement for wall batts.

A quarter of the weight

InstaPanel weighs just over a quarter as much as fibre cement: roughly 185 kg on a 50 m² wall, against about 650 kg. That helps on upper storeys, lightweight frames and sites with tight access.

8 · Safety

Cutting and silica safety

Fibre cement contains crystalline silica

James Hardie's instructions say to cut with a Hardie™ knife, guillotine or fibreshears where possible, or with a dust-reducing circular saw connected to an M-class vacuum. Wear a P2 respirator, never dry sweep, and never use a grinder. SafeWork NSW requires silica controls for this work.

✔ InstaPanel is cut with an angle grinder or circular saw using normal PPE, and the cut edges are covered with trims.

9 · Upkeep

Maintenance and warranty: fewer headaches

InstaPanel needs no painting at all. Its pre-finished metal face is designed to resist fading and cracking, and the tongue-and-groove joints interlock and are sealed. There's no paint film to crack, peel or let water in, so you just wash it down and check sealant and trims now and then. InstaPanel comes with a 20-year warranty and can last up to 25 years.

Fibre cement needs its paint maintained, with a repaint every 7–10 years. James Hardie gives Fine Texture and Axon™ a 25-year product warranty; the paint is covered separately by the paint maker. Over 25 years, InstaPanel's no-paint finish keeps it the cheaper wall by a wide margin.

10 · Which one should you choose?

Pros and cons

InstaPanel

Pros

  • ✔Lowest supply & install cost, about $118/m² all-in
  • ✔No painting, ever: no repaint every 7–10 years
  • ✔Fewer headaches: anti-crack face, sealed interlocking joints, nothing to peel
  • ✔20-year warranty; can last up to 25 years
  • ✔Non-combustible steel face; fine for house walls 900mm+ from the boundary
  • ✔3.7 kg/m²: easy to lift, ideal for upper levels and lightweight frames
  • ✔Built-in PU insulation and noise reduction
  • ✔Fast (~2 days for 50 m²), no silica dust

Cons

  • ✖Not within 900mm of a boundary or 1800mm of another building
  • ✖PU core is combustible: not for fire-rated walls; no BAL rating published
  • ✖Two colours only (Grey 801, White 802)
  • ✖Studs at 450mm max; battens recommended

Hardie™ Fine Texture

Pros

  • ✔Non-combustible, BAL-40
  • ✔Can form part of fire-rated and boundary-wall systems
  • ✔25-year warranty
  • ✔Paint any colour; render look without render
  • ✔Large 1200mm sheets, few joints

Cons

  • ✖About $163/m² all-in
  • ✖Pre-sealed only: primer + 2 coats within 3 months, then repaint every 7–10 years (est. $40/m² each time)
  • ✖13.1 kg/m²; sheets up to 57 kg
  • ✖Silica dust controls needed when cutting

Hardie™ Axon™ 133

Pros

  • ✔Non-combustible, BAL-40
  • ✔25-year warranty
  • ✔Classic vertical-joint (VJ) timber look
  • ✔Paint any colour

Cons

  • ✖Highest cost, about $172/m² all-in
  • ✖Pre-sealed only: primer + 2 coats, then repaint every 7–10 years
  • ✖13 kg/m²; sheets up to 56 kg
  • ✖Silica dust controls needed
  • ✖Dearer corner trims

Our recommendation

  • ➜Choose InstaPanel for most granny flats, extensions, sheds, carports and feature walls. You get the lowest installed cost, the lowest 25-year cost, a faster job, lighter panels and no painting, ever. Check it sits at least 900mm from the boundary and 1800mm from other buildings, and check bushfire requirements with your certifier.
  • ➜Choose Hardie™ Fine Texture for a render look in any colour, or where BAL-40 or a boundary or fire-rated wall system is needed.
  • ➜Choose Axon™ 133 for a painted VJ timber look with the same fire performance and warranty as Fine Texture.
11 · FAQ

Frequently asked questions

Does InstaPanel need painting?

No, never. It comes pre-finished in Grey 801 or White 802, so there's no painter and no repaint bill. Fibre cement arrives pre-sealed only, so it must be primed and painted on site, then repainted every 7–10 years.

Can InstaPanel be used on a boundary wall?

No. Devox's installation guide says it must not be installed less than 900mm from an allotment boundary or 1800mm from another building, and it isn't for fire-rated walls.

Can I fix InstaPanel straight to the studs?

The Devox guide doesn't recommend it unless the project engineer approves. Use 40×25mm H2/H3 battens on studs at 450mm centres or less.

Is fibre cement better in bushfire areas?

For BAL-29 and above, yes: Hardie™ Fine Texture and Axon™ are listed to BAL-40, and Devox doesn't publish a BAL rating for InstaPanel. At BAL-12.5 and BAL-19, AS 3959 has no material rule for wall parts 400mm or more above the ground, decks or low roofs, so InstaPanel can often be used there; your certifier confirms.

Do termites eat InstaPanel?

No. It's not termite food: steel is termite-resistant (CSIRO) and termites don't eat PU foam.

How long does InstaPanel last?

InstaPanel comes with a 20-year warranty and can last up to 25 years, with no painting. James Hardie gives a 25-year product warranty on Fine Texture and Axon™, but the paint needs redoing every 7–10 years.

Will InstaPanel crack or leak?

Devox designs the panel to resist cracking and fading, and the interlocking joints are sealed. There's no paint film to crack or peel. Like any cladding, it relies on correct wall wrap and flashings behind it.

Are these prices a quote?

No. They're indicative prices from November 2026. Send us your plans for a written supply quote.

12 · Get a quote

Finish faster, pay less, never paint: get your InstaPanel quote

Send us your plans or wall sizes and we'll send back an itemised quote for panels, trims, battens and wall wrap, with lengths chosen to cut waste.

We stock InstaPanel in Grey 801 and White 802, plus Hardie™ Fine Texture, Axon™ Cladding and the trims, battens and wall wrap to go with them. Browse our cladding range or contact us. Call 02 4605 0215, email sales@alphatimber.com.au, or visit us at 10 Lancaster Street, Ingleburn NSW 2565 (Mon–Fri 6am–4pm, Sat 6am–3pm).

Get your InstaPanel quote

Call us, email your plans, or send a quote request. We'll price panels, trims, battens and wall wrap for your job.

Sources: Alpha Timber prices and stock (16 Nov 2026); Devox InstaPanel PU installation guide and warranty; James Hardie Fine Texture and Axon™ product pages, Fine Texture installation guide and 25 Years Product Warranty (April 2026); SafeWork NSW; published 2026 Australian cladding and painting cost guides (PC Carpentry, Yakka Labour, MyTradeCrew/What's The Damage, The Quote Yard, Proview Painting). InstaPanel warranty and lifespan as advised by Alpha Timber. Fire and bushfire notes from the NCC Housing Provisions Part 9.2, NCC C2D10 and AS 3959; termite notes from CSIRO; typical R-values from published data for 16mm PU-core metal siding panels and the NCC fibre cement value. Waste allowance, painting (primer + 2 coats), repaint costs and intervals are estimates. Hardie™, Fine Texture and Axon™ are trademarks of James Hardie Technology Limited. InstaPanel is a Devox product.