{"title":"Pergola","description":"\u003cp\u003ePosts, beams, rafters and brackets for a pergola or patio: H3 primed posts and GL10 beams, primed DAR, pergola angles, post supports, bolts and concrete.\u003c\/p\u003e","products":[{"product_id":"88x88-h4-dar-gl8-treated-pine-post","title":"88 x 88 H4 treated pine post, GL8 laminated, DAR, 3.6 to 6.0 m","description":"\u003cp\u003eThis is an 88 x 88 mm H4 treated pine post, GL8 glue-laminated and dressed all round (DAR). H4 treatment is for timber in contact with the ground, so it is used for pergola, carport, deck and fence posts set in the ground.\u003c\/p\u003e\u003ch2\u003eKey facts\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSize: 88 x 88 mm\u003c\/li\u003e\n\u003cli\u003eLengths: 3.6, 4.8, 5.4 and 6.0 m\u003c\/li\u003e\n\u003cli\u003eGrade: GL8 glue-laminated (glulam)\u003c\/li\u003e\n\u003cli\u003eTimber: treated pine\u003c\/li\u003e\n\u003cli\u003eTreatment: H4, for outdoor use in contact with the ground\u003c\/li\u003e\n\u003cli\u003eFinish: dressed all round (DAR)\u003c\/li\u003e\n\u003cli\u003eWeight: about 4.3 kg per metre (about 15 kg for 3.6 m, 26 kg for 6.0 m)\u003c\/li\u003e\n\u003cli\u003eSold as: single lengths\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\u003cp\u003ePosts set in the ground for pergolas, carports, decks, fences and landscaping. Glue-laminated construction helps keep the post straight, and the dressed faces are smooth to handle and fix to. If your post will sit on a stirrup above the ground and be painted, see the \u003ca href=\"\/products\/88x88-gl8-h3-primed-treated-post\"\u003e88 x 88 GL8 H3 primed post\u003c\/a\u003e or the \u003ca href=\"\/products\/112x112-gl8-h3-primed-treated-post\"\u003e112 x 112 GL8 H3 primed post\u003c\/a\u003e.\u003c\/p\u003e\u003ch2\u003eWorking with it\u003c\/h2\u003e\u003cp\u003ePost size, height, depth in the ground and footings are structural: follow your plans or ask your engineer. Where you can, put the uncut end in the ground and keep cut ends up. Seal any cut ends, notches and holes with an end-seal preservative. Use hot dipped galvanised or stainless steel fixings. Wear gloves, a dust mask and eye protection when cutting treated timber, and do not burn the offcuts. Store posts flat on bearers, off the ground, until they go in.\u003c\/p\u003e\u003ch2\u003eCommon questions\u003c\/h2\u003e\u003ch3\u003eCan it go in the ground?\u003c\/h3\u003e\u003cp\u003eYes. H4 is the treatment level for timber in contact with the ground. Your plans or engineer set the depth and the footing.\u003c\/p\u003e\u003ch3\u003eIs an 88 x 88 post the same as a 90 x 90 post?\u003c\/h3\u003e\u003cp\u003eIt measures 88 x 88 mm after dressing. Posts this size are often called 90 x 90, so check that your stirrup or bracket suits an 88 mm post.\u003c\/p\u003e\u003ch3\u003eHow heavy is it?\u003c\/h3\u003e\u003cp\u003eAbout 4.3 kg per metre. A 3.6 m post is about 15 kg and a 6.0 m post is about 26 kg.\u003c\/p\u003e\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\u003cp\u003eYes. Pick up from our yard at 10 Lancaster Street, Ingleburn, or have it delivered across Sydney. Lengths run to 6.0 m, so bring a vehicle that can carry them or call (02) 4605 0215 for a delivery quote.\u003c\/p\u003e","brand":"Alpha Timber","offers":[{"title":"3.6m","offer_id":47896292852023,"sku":"23528","price":91.0,"currency_code":"AUD","in_stock":false},{"title":"4.8m","offer_id":50203811152183,"sku":"23528.2","price":121.33,"currency_code":"AUD","in_stock":true},{"title":"5.4m","offer_id":50203811709239,"sku":"23528.3","price":136.5,"currency_code":"AUD","in_stock":true},{"title":"6.0m","offer_id":50203812659511,"sku":"23528.4","price":151.67,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/files\/88x88-h4-gl8-laminated-treated-pine-post-dar-alpha-timber.png?v=1795061161"},{"product_id":"185x42-h3-pre-primed-dar","title":"185x42 H3 Pre Primed DAR","description":"\u003cp\u003eThe \u003cstrong\u003e185x42 H3 Pre Primed DAR\u003c\/strong\u003e is finger-jointed radiata pine, dressed all round (DAR), H3 LOSP treated and factory coated with a pink primer, ready for your top coats. H3 treatment makes it suitable for above-ground outdoor use.\u003c\/p\u003e\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eSize:\u003c\/strong\u003e 185 mm x 42 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLengths:\u003c\/strong\u003e as listed in the options above\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSpecies:\u003c\/strong\u003e plantation radiata pine, finger-jointed and kiln dried\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTreatment:\u003c\/strong\u003e H3 LOSP, above-ground exterior\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFinish:\u003c\/strong\u003e pink primer, ready for top coats\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eFeatures\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eTreated against fungal decay and insect attack for above-ground outdoor use\u003c\/li\u003e\n\u003cli\u003eFinger-jointed and kiln dried for straight, stable lengths\u003c\/li\u003e\n\u003cli\u003eSmooth dressed faces, pre-primed to save painting time\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eCommon uses\u003c\/h2\u003e\n\u003cp\u003eOutdoor framing, pergola and deck trims, battens, handrail supports and outdoor joinery. Seal any cut ends, notches and holes with a suitable end sealer before top coating, and apply two or more coats of quality exterior paint.\u003c\/p\u003e\n\u003ch2\u003ePick up or delivery\u003c\/h2\u003e\n\u003cp\u003ePick up from our yard at 10 Lancaster Street, Ingleburn, or ask us to quote delivery to your site anywhere in Sydney.\u003c\/p\u003e","brand":"Alpha Timber","offers":[{"title":"3.6m","offer_id":47896284856631,"sku":"201515","price":109.33,"currency_code":"AUD","in_stock":false},{"title":"4.2m","offer_id":47896540381495,"sku":"201516","price":127.55,"currency_code":"AUD","in_stock":false},{"title":"4.8m","offer_id":47896540414263,"sku":"201517","price":145.78,"currency_code":"AUD","in_stock":true},{"title":"5.4m","offer_id":47896540447031,"sku":"201518","price":164.0,"currency_code":"AUD","in_stock":false},{"title":"6.0m","offer_id":47896540479799,"sku":"201519","price":182.22,"currency_code":"AUD","in_stock":true},{"title":"7.2m","offer_id":47896540512567,"sku":"201520","price":218.66,"currency_code":"AUD","in_stock":false},{"title":"2.7m","offer_id":50199189389623,"sku":"24498","price":82.0,"currency_code":"AUD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/files\/185x42-h3-pre-primed-dar-pink-primed-pine-alpha-timber.png?v=1795071416"},{"product_id":"138x42-h3-pre-primed-dar","title":"138x42 H3 Pre Primed DAR","description":"\u003cp\u003eThe \u003cstrong\u003e138x42 H3 Pre Primed DAR\u003c\/strong\u003e is finger-jointed radiata pine, dressed all round (DAR), H3 LOSP treated and factory coated with a pink primer, ready for your top coats. H3 treatment makes it suitable for above-ground outdoor use.\u003c\/p\u003e\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eSize:\u003c\/strong\u003e 138 mm x 42 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLengths:\u003c\/strong\u003e as listed in the options above\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSpecies:\u003c\/strong\u003e plantation radiata pine, finger-jointed and kiln dried\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTreatment:\u003c\/strong\u003e H3 LOSP, above-ground exterior\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFinish:\u003c\/strong\u003e pink primer, ready for top coats\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eFeatures\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eTreated against fungal decay and insect attack for above-ground outdoor use\u003c\/li\u003e\n\u003cli\u003eFinger-jointed and kiln dried for straight, stable lengths\u003c\/li\u003e\n\u003cli\u003eSmooth dressed faces, pre-primed to save painting time\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eCommon uses\u003c\/h2\u003e\n\u003cp\u003eOutdoor framing, pergola and deck trims, battens, handrail supports and outdoor joinery. Seal any cut ends, notches and holes with a suitable end sealer before top coating, and apply two or more coats of quality exterior paint.\u003c\/p\u003e\n\u003ch2\u003ePick up or delivery\u003c\/h2\u003e\n\u003cp\u003ePick up from our yard at 10 Lancaster Street, Ingleburn, or ask us to quote delivery to your site anywhere in Sydney.\u003c\/p\u003e","brand":"Alpha Timber","offers":[{"title":"4.2m","offer_id":47896284823863,"sku":"201502","price":95.98,"currency_code":"AUD","in_stock":false},{"title":"4.8m","offer_id":47896540184887,"sku":"201503","price":109.68,"currency_code":"AUD","in_stock":true},{"title":"5.4m","offer_id":47896540217655,"sku":"201504","price":123.39,"currency_code":"AUD","in_stock":false},{"title":"6.0m","offer_id":47896540250423,"sku":"201505","price":137.1,"currency_code":"AUD","in_stock":false},{"title":"3.6m","offer_id":50198833266999,"sku":"201501","price":82.27,"currency_code":"AUD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/files\/138x42-h3-pre-primed-dar-pink-primed-pine-alpha-timber.png?v=1795071416"},{"product_id":"88x88-gl8-h3-primed-treated-post","title":"88 x 88 H3 primed GL8 glulam post, treated pine, 2.4 to 6.0 m","description":"\u003cp\u003e88 x 88 mm H3 primed GL8 post: a glue-laminated (glulam) radiata pine post, H3 LOSP treated and factory coated in a pink primer. It is used for posts above ground, such as pergola, carport, verandah and deck posts.\u003c\/p\u003e\u003ch2\u003eKey facts\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSize: 88 x 88 mm (often asked for as a 90 x 90 post)\u003c\/li\u003e\n\u003cli\u003eLengths: 2.4, 2.7, 3.0, 3.6, 4.2, 4.8, 5.4 and 6.0 m\u003c\/li\u003e\n\u003cli\u003eGrade: GL8 glue-laminated (glulam)\u003c\/li\u003e\n\u003cli\u003eTimber: radiata pine\u003c\/li\u003e\n\u003cli\u003eTreatment: H3 LOSP, for outdoor use above ground\u003c\/li\u003e\n\u003cli\u003eFinish: pink primer, ready for top coats\u003c\/li\u003e\n\u003cli\u003eWeight: about 5 kg per metre (about 15 kg for 3.0 m, 30 kg for 6.0 m)\u003c\/li\u003e\n\u003cli\u003eSold as: single lengths\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\u003cp\u003ePergola, carport and verandah posts, deck posts and feature framing above ground. Glue-laminated construction keeps the post straight and stable. H3 treatment is for outdoor timber that is clear of the ground, so the post must sit on a stirrup or bracket and not in the ground. For bigger posts, see \u003ca href=\"\/products\/112x112-gl8-h3-primed-treated-post\"\u003e112 x 112 GL8 H3 primed post\u003c\/a\u003e and \u003ca href=\"\/products\/135x135-gl8-h3-primed-treated-post\"\u003e135 x 135 GL8 H3 primed post\u003c\/a\u003e. For a post that goes in the ground, see the \u003ca href=\"\/products\/88x88-h4-dar-gl8-treated-pine-post\"\u003e88 x 88 H4 treated pine post\u003c\/a\u003e.\u003c\/p\u003e\u003ch2\u003eWorking with it\u003c\/h2\u003e\u003cp\u003ePost sizes, heights and footings are structural: follow your plans or ask your engineer. Seal any cut ends, notches and holes with a suitable end sealer before top coating. The pink primer is an undercoat, so apply two or more coats of quality exterior paint and keep the paint maintained. Store posts flat on bearers, off the ground and under cover until they are fixed. Use hot dipped galvanised or stainless steel fixings outdoors.\u003c\/p\u003e\u003ch2\u003eCommon questions\u003c\/h2\u003e\u003ch3\u003eIs 88 x 88 the same as a 90 x 90 post?\u003c\/h3\u003e\u003cp\u003e88 x 88 mm is the finished, dressed size, and it is often called a 90 x 90 post. Check that your post support suits an 88 mm post.\u003c\/p\u003e\u003ch3\u003eCan it go in the ground?\u003c\/h3\u003e\u003cp\u003eNo. H3 is for outdoor use above ground. Fix the post to a post support that holds it clear of the ground. Timber in the ground needs H4 treatment or higher.\u003c\/p\u003e\u003ch3\u003eHow heavy is it?\u003c\/h3\u003e\u003cp\u003eAbout 5 kg per metre. A 3.0 m post is about 15 kg and a 6.0 m post is about 30 kg.\u003c\/p\u003e\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\u003cp\u003eYes. Pick up from our yard at 10 Lancaster Street, Ingleburn, or have it delivered across Sydney. Lengths run to 6.0 m, so bring a vehicle that can carry them or call (02) 4605 0215 for a delivery quote.\u003c\/p\u003e","brand":"Alpha Timber","offers":[{"title":"2.4m","offer_id":50203829535031,"sku":"201536","price":76.8,"currency_code":"AUD","in_stock":true},{"title":"2.7m","offer_id":47896284234039,"sku":"201537","price":86.4,"currency_code":"AUD","in_stock":true},{"title":"3.0m","offer_id":47896539988279,"sku":"201538","price":96.0,"currency_code":"AUD","in_stock":true},{"title":"3.6m","offer_id":47896540021047,"sku":"201539","price":115.2,"currency_code":"AUD","in_stock":true},{"title":"4.2m","offer_id":47896540053815,"sku":"201539.1","price":134.4,"currency_code":"AUD","in_stock":true},{"title":"4.8m","offer_id":47896540086583,"sku":"201540","price":153.6,"currency_code":"AUD","in_stock":true},{"title":"5.4m","offer_id":47896540119351,"sku":"201541","price":172.8,"currency_code":"AUD","in_stock":true},{"title":"6.0m","offer_id":47896540152119,"sku":"201542","price":192.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/files\/88x88-gl8-h3-primed-treated-post-pink-primed-alpha-timber.png?v=1795071522"},{"product_id":"fedtrim-post-cover-and-support-kit","title":"Fedtrim post cover and support kit for 112 to 135 mm posts, large","description":"\u003cp\u003eThe large Fedtrim post cover and support kit is for timber posts 112 to 135 mm across. As the name says, the kit combines a post support with a cover that trims the base of the post, for a neat finish on verandah, pergola and carport posts.\u003c\/p\u003e\u003ch2\u003eKey facts\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eBrand: Fedtrim\u003c\/li\u003e\n\u003cli\u003eSuits posts: 112 to 135 mm\u003c\/li\u003e\n\u003cli\u003eKit type: post cover and support kit, large\u003c\/li\u003e\n\u003cli\u003eSold as: one kit, for one post\u003c\/li\u003e\n\u003cli\u003eSmaller size: a kit for 90 to 100 mm posts is also stocked\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\u003cp\u003eThe base of larger timber posts on verandahs, pergolas, carports and decks, where you want the foot of the post supported and trimmed. Measure your post before ordering. This kit is listed for posts 112 to 135 mm, which takes in 112 x 112 mm posts and our \u003ca href=\"\/products\/135x135-gl8-h3-primed-treated-post\"\u003e135 x 135 H3 primed posts\u003c\/a\u003e. For smaller posts, see the \u003ca href=\"\/products\/fedtrim-90-100mm-post-cover-and-support-kit\"\u003eFedtrim kit for 90 to 100 mm posts\u003c\/a\u003e.\u003c\/p\u003e\u003ch2\u003eInstallation\u003c\/h2\u003e\u003cp\u003eFollow the instructions packed with the kit. Fixing a post to a slab or footing is structural. The anchors, and the tie-down for the roof the post carries, come from your plans, AS 1684 or your engineer. Keep the foot of a timber post clear of the ground and of pooling water. Seal the cut ends of treated or primed posts before you fit the kit.\u003c\/p\u003e\u003ch2\u003eCommon questions\u003c\/h2\u003e\u003ch3\u003eWhat post sizes does it fit?\u003c\/h3\u003e\u003cp\u003eIt is listed for posts 112 to 135 mm. For posts 90 to 100 mm, order the smaller kit.\u003c\/p\u003e\u003ch3\u003eWhat is in the kit?\u003c\/h3\u003e\u003cp\u003eThe kit contents, material and finish are not listed online yet. Call (02) 4605 0215 and we will check the pack for you.\u003c\/p\u003e\u003ch3\u003eHow many do I need?\u003c\/h3\u003e\u003cp\u003eOne kit for each post.\u003c\/p\u003e\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\u003cp\u003eYes. Pick up from our yard at 10 Lancaster Street, Ingleburn, or have it delivered across Sydney with your posts and the rest of your order.\u003c\/p\u003e","brand":"Alpha Timber","offers":[{"title":"Default Title","offer_id":47896283709751,"sku":"221","price":29.99,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/Fedtrim-112-135mm-Post-Cover-and-Support_Kit-Large.png?v=1766023787"},{"product_id":"multigrip-100mm-box-50","title":"Multigrip framing anchor 100 mm, box of 50","description":"\u003cp\u003eA multigrip is a steel framing anchor with punched nail holes, used to tie together two timbers that cross or meet at right angles. This is the 100 mm size, sold in a box of 50.\u003c\/p\u003e\u003ch2\u003eKey facts\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eType: multigrip framing anchor\u003c\/li\u003e\n\u003cli\u003eSize: 100 mm\u003c\/li\u003e\n\u003cli\u003eMaterial: steel\u003c\/li\u003e\n\u003cli\u003eBox quantity: 50\u003c\/li\u003e\n\u003cli\u003eSold as: box of 50\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\u003cp\u003eTying rafters and trusses to top plates, joists to bearers, and similar timber to timber joints in house frames, pergolas and decks. The anchor is nailed to both timbers and helps hold the joint against wind uplift and sideways movement. For joists that hang off the face of a beam, see our \u003ca href=\"\/products\/45x90mm-joist-hanger-box-45\"\u003ejoist hangers\u003c\/a\u003e. For strap tie-down, see \u003ca href=\"\/products\/hoop-iron\"\u003ehoop iron strapping\u003c\/a\u003e.\u003c\/p\u003e\u003ch2\u003eInstallation\u003c\/h2\u003e\u003cp\u003eSit the anchor tight against both timbers and nail through the punched holes into each one. Use the connector nails the anchor maker specifies, and fill the number of holes your tie-down detail calls for. The strength of the joint depends on the number of anchors and nails, so tie-down for roofs, pergolas and decks must follow your plans, AS 1684 or your engineer. Use galvanised nails outdoors.\u003c\/p\u003e\u003ch2\u003eCommon questions\u003c\/h2\u003e\u003ch3\u003eHow many multigrips are in a box?\u003c\/h3\u003e\u003cp\u003eThis listing is a box of 50 anchors.\u003c\/p\u003e\u003ch3\u003eHow many do I need for each rafter or truss?\u003c\/h3\u003e\u003cp\u003eThat comes from the tie-down detail on your plans or from AS 1684 for your wind class. Some joints need one anchor, some need a pair, and some need a strap or bolt instead. Ask your builder or engineer if the plans do not say.\u003c\/p\u003e\u003ch3\u003eAre they galvanised?\u003c\/h3\u003e\u003cp\u003eThe finish and steel thickness are not listed online yet. Call us on (02) 4605 0215 before ordering if the anchors will be used outdoors, near the coast or with treated timber.\u003c\/p\u003e\u003ch3\u003eCan I pick them up or get them delivered?\u003c\/h3\u003e\u003cp\u003eYes. Pick up from our yard at 10 Lancaster Street, Ingleburn, or we can deliver across Sydney.\u003c\/p\u003e","brand":"Alpha Timber","offers":[{"title":"Default Title","offer_id":47153518805303,"sku":"704481","price":29.99,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/MULTIGRIP-100MM.png?v=1754676138"},{"product_id":"14gx100-gal-batten-screw-pk-100","title":"14gx100 Gal batten screw Pk 100 LS114","description":"\u003ch1\u003e14gx100 Gal batten screw Pk 100 LS114\u003c\/h1\u003e\n\u003cp\u003eIntroducing the 14gx100 Gal batten screw Pk 100 LS114, a high-quality and durable product designed to meet all your construction needs. This galvanized batten screw is perfect for securing battens and other timber materials, ensuring a strong and reliable connection.\u003c\/p\u003e\n\u003ch2\u003eSpecifications:\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eSize: 14 gauge x 100mm\u003c\/li\u003e\n\u003cli\u003eMaterial: Galvanized steel\u003c\/li\u003e\n\u003cli\u003eQuantity: Pack of 100 screws\u003c\/li\u003e\n\u003cli\u003eModel: LS114\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eAdvantages:\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eHigh-quality galvanized steel for superior strength and corrosion resistance\u003c\/li\u003e\n\u003cli\u003eDesigned specifically for securing battens and timber materials\u003c\/li\u003e\n\u003cli\u003eComes in a pack of 100 screws, providing ample supply for your projects\u003c\/li\u003e\n\u003cli\u003eReliable and durable construction ensures long-lasting performance\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eUpgrade your construction projects with the 14gx100 Gal batten screw Pk 100 LS114, available exclusively at Alpha Timber. Order now and experience the difference!\u003c\/p\u003e","brand":"Alpha Timber","offers":[{"title":"Default Title","offer_id":47748381311287,"sku":"14752","price":24.99,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/14gx50-Gal-batten-screw.png?v=1754676038"},{"product_id":"12x99mm-gal-hex-masonbolt-box25","title":"12x99mm GAL HEX MASONBOLT BOX25 SA15","description":"\u003ch1\u003e12x99mm GAL HEX MASONBOLT BOX25 SA15\u003c\/h1\u003e\u003cp\u003eIntroducing the 12x99mm GAL HEX MASONBOLT BOX25 SA15, a high-quality and durable product designed to meet all your construction needs. This versatile mason bolt is perfect for various applications, ensuring a secure and reliable connection every time.\u003c\/p\u003e\u003ch2\u003eSpecifications:\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSize: 12x99mm\u003c\/li\u003e\n\u003cli\u003eMaterial: Galvanized steel\u003c\/li\u003e\n\u003cli\u003eType: Hex mason bolt\u003c\/li\u003e\n\u003cli\u003eQuantity: 25 pieces per box\u003c\/li\u003e\n\u003cli\u003eSA15 compliant\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eAdvantages:\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eStrong and sturdy construction for enhanced durability\u003c\/li\u003e\n\u003cli\u003eGalvanized coating provides excellent corrosion resistance\u003c\/li\u003e\n\u003cli\u003eHex design ensures a secure and tight fit\u003c\/li\u003e\n\u003cli\u003eComes in a convenient box of 25 pieces\u003c\/li\u003e\n\u003cli\u003eSA15 compliant for meeting safety standards\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eUpgrade your construction projects with the 12x99mm GAL HEX MASONBOLT BOX25 SA15 available at Alpha Timber. Order now and experience the reliability and quality this product has to offer!\u003c\/p\u003e","brand":"Alpha Timber","offers":[{"title":"Default Title","offer_id":47748381147447,"sku":"641011","price":49.99,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/12x99mm-GAL-HEX-MASONBOLT-BOX25-SA15.png?v=1765761001"},{"product_id":"angle-pergola-88x63x36x1-6mm-box-50","title":"ANGLE PERGOLA 88X63X36X1.6mm Box\/50","description":"\u003ch1\u003eANGLE PERGOLA 88X63X36X1.6mm Box\/50\u003c\/h1\u003e\n\u003cp\u003eIntroducing the ANGLE PERGOLA 88X63X36X1.6mm Box\/50, a versatile and durable product designed to enhance your outdoor space. This pergola is made from high-quality materials and is built to withstand the elements, ensuring long-lasting performance.\u003c\/p\u003e\n\n\u003ch2\u003eSpecifications:\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eDimensions: 88X63X36X1.6mm\u003c\/li\u003e\n\u003cli\u003eQuantity: Box of 50\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eProduct Advantages:\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eSturdy construction for enhanced durability\u003c\/li\u003e\n\u003cli\u003eWeather-resistant materials for long-lasting performance\u003c\/li\u003e\n\u003cli\u003eEasy to install and maintain\u003c\/li\u003e\n\u003cli\u003eProvides shade and protection from the sun\u003c\/li\u003e\n\u003cli\u003eEnhances the aesthetic appeal of your outdoor space\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eUpgrade your outdoor area with the ANGLE PERGOLA 88X63X36X1.6mm Box\/50 and create a stylish and functional space for relaxation and entertainment. Shop now at Alpha Timber!\u003c\/p\u003e","brand":"Alpha Timber","offers":[{"title":"Default Title","offer_id":47796300218679,"sku":"704485","price":0.99,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/ANGLE-PERGOLA-88X63X36X1.6mm_Box_50.jpg?v=1765950709"},{"product_id":"bolt-nut-cup-gal-12x100","title":"Bolt \u0026 Nut Cup Gal 12x100","description":"\u003ch1\u003eBolt \u0026amp; Nut Cup Gal 12x100\u003c\/h1\u003e\n\u003cp\u003eIntroducing the Bolt \u0026amp; Nut Cup Gal 12x100, a high-quality and durable fastening solution for all your construction needs. This product is designed to provide secure and reliable connections, ensuring the safety and stability of your projects.\u003c\/p\u003e\n\n\u003ch2\u003eSpecifications:\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eSize: 12x100\u003c\/li\u003e\n\u003cli\u003eMaterial: Galvanized steel\u003c\/li\u003e\n\u003cli\u003eType: Bolt \u0026amp; Nut Cup\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eAdvantages:\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eStrong and sturdy construction for long-lasting performance\u003c\/li\u003e\n\u003cli\u003eGalvanized steel material offers excellent corrosion resistance\u003c\/li\u003e\n\u003cli\u003eEasy to install and provides a secure connection\u003c\/li\u003e\n\u003cli\u003ePerfect for various construction applications\u003c\/li\u003e\n\u003cli\u003eReliable and dependable for both residential and commercial projects\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eUpgrade your construction projects with the Bolt \u0026amp; Nut Cup Gal 12x100 today! Visit Alpha Timber for the best deals.\u003c\/p\u003e","brand":"Alpha Timber","offers":[{"title":"Default Title","offer_id":47796301594935,"sku":"32144","price":2.29,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/Bolt-Nut-Cup-12x100.png?v=1766021752"},{"product_id":"45x180mm-joist-hanger-box-30","title":"Joist hanger 45 x 180 mm, box of 30","description":"\u003cp\u003eThese are 45 x 180 mm joist hangers, sold in a box of 30. Each hanger takes a 45 mm wide timber joist and fixes it to the face of a bearer, beam or ledger on floor and deck framing.\u003c\/p\u003e\u003ch2\u003eKey facts\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSize: 45 x 180 mm\u003c\/li\u003e\n\u003cli\u003eSuits: 45 mm wide timber joists\u003c\/li\u003e\n\u003cli\u003eMaterial: steel\u003c\/li\u003e\n\u003cli\u003ePack: box of 30 hangers\u003c\/li\u003e\n\u003cli\u003eSold as: box\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\u003cp\u003eHanging floor joists and deck joists off the side of a bearer, beam or wall ledger where the joist cannot sit on top. Hangers are also used on trimmers around stair and floor openings.\u003c\/p\u003e\u003ch2\u003eInstallation\u003c\/h2\u003e\u003cp\u003eSeat the joist fully in the hanger and hard against the supporting timber. Fix through the holes the hanger maker specifies, with the nails or screws it specifies. The load a hanger carries depends on the number and type of fixings, so do not swap them for whatever is in the gun. Outdoors and in treated pine use hot dipped galvanised or stainless steel fixings. For the load on a joist hanger, follow your plans or your engineer.\u003c\/p\u003e\u003ch2\u003eCommon questions\u003c\/h2\u003e\u003ch3\u003eWhich joists does it suit?\u003c\/h3\u003e\u003cp\u003eTimber 45 mm wide, such as 45 mm MGP10 pine or 45 mm LVL. The right hanger height for a joist depth comes from the hanger maker's table or your engineer.\u003c\/p\u003e\u003ch3\u003eHow many do I need?\u003c\/h3\u003e\u003cp\u003eOne hanger for each joist end that is hung. A box holds 30.\u003c\/p\u003e\u003ch3\u003eWhat nails or screws do I use?\u003c\/h3\u003e\u003cp\u003eUse the fixings the hanger maker specifies and fill the holes it calls for. Fewer or lighter fixings reduce the load the hanger can carry.\u003c\/p\u003e\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\u003cp\u003eYes. Pick up from our yard at 10 Lancaster Street, Ingleburn, or have it delivered across Sydney. Call (02) 4605 0215 for a delivery quote.\u003c\/p\u003e","brand":"Alpha Timber","offers":[{"title":"Default Title","offer_id":47796303692087,"sku":"700003","price":2.95,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/45x180mm-Joist-Hanger-Box_30.png?v=1765853563"},{"product_id":"fedtrim-90-100mm-post-cover-and-support-kit","title":"Fedtrim post cover and support kit for 90 to 100 mm posts","description":"\u003cp\u003eThe Fedtrim post cover and support kit is for timber posts 90 to 100 mm across. As the name says, the kit combines a post support with a cover that trims the base of the post, for a neat finish on verandah, pergola and carport posts.\u003c\/p\u003e\u003ch2\u003eKey facts\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eBrand: Fedtrim\u003c\/li\u003e\n\u003cli\u003eSuits posts: 90 to 100 mm\u003c\/li\u003e\n\u003cli\u003eKit type: post cover and support kit\u003c\/li\u003e\n\u003cli\u003eSold as: one kit, for one post\u003c\/li\u003e\n\u003cli\u003eLarger size: a kit for 112 to 135 mm posts is also stocked\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\u003cp\u003eThe base of timber posts on verandahs, pergolas, carports and decks, where you want the foot of the post supported and trimmed. Measure your post before ordering. This kit is listed for posts 90 to 100 mm. Dressed 88 x 88 mm posts, such as our \u003ca href=\"\/products\/88x88-gl8-h3-primed-treated-post\"\u003e88 x 88 H3 primed posts\u003c\/a\u003e, sit just under that range, so check the fit with us first. For bigger posts, see the \u003ca href=\"\/products\/fedtrim-post-cover-and-support-kit\"\u003eFedtrim kit for 112 to 135 mm posts\u003c\/a\u003e.\u003c\/p\u003e\u003ch2\u003eInstallation\u003c\/h2\u003e\u003cp\u003eFollow the instructions packed with the kit. Fixing a post to a slab or footing is structural. The anchors, and the tie-down for the roof the post carries, come from your plans, AS 1684 or your engineer. Keep the foot of a timber post clear of the ground and of pooling water. Seal the cut ends of treated or primed posts before you fit the kit.\u003c\/p\u003e\u003ch2\u003eCommon questions\u003c\/h2\u003e\u003ch3\u003eWhat post sizes does it fit?\u003c\/h3\u003e\u003cp\u003eIt is listed for posts 90 to 100 mm. For posts 112 to 135 mm, order the large kit.\u003c\/p\u003e\u003ch3\u003eWhat is in the kit?\u003c\/h3\u003e\u003cp\u003eThe kit contents, material and finish are not listed online yet. Call (02) 4605 0215 and we will check the pack for you.\u003c\/p\u003e\u003ch3\u003eHow many do I need?\u003c\/h3\u003e\u003cp\u003eOne kit for each post.\u003c\/p\u003e\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\u003cp\u003eYes. Pick up from our yard at 10 Lancaster Street, Ingleburn, or have it delivered across Sydney with your posts and the rest of your order.\u003c\/p\u003e","brand":"Alpha Timber","offers":[{"title":"Default Title","offer_id":47796304118071,"sku":"220","price":19.99,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/Fedtrim-90-100mm_Post-Cover-and-Support-Kit.png?v=1766023665"},{"product_id":"post-support-bolt-down-90mm-post-b25c","title":"Bolt down post support for 90 mm posts","description":"\u003cp\u003eThis is a bolt down post support sized for a 90 mm timber post. It bolts to a concrete slab or footing and holds the base of the post on decks, pergolas and similar outdoor structures. It is also known as a post stirrup or post anchor.\u003c\/p\u003e\n\u003ch2\u003eKey facts\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eType: bolt down post support (post stirrup)\u003c\/li\u003e\n\u003cli\u003eSuits: 90 mm post\u003c\/li\u003e\n\u003cli\u003eMaterial: steel\u003c\/li\u003e\n\u003cli\u003eFixing: bolts down to a cured concrete slab or footing\u003c\/li\u003e\n\u003cli\u003eSold as: each\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\n\u003cp\u003eFixing the bottom of a 90 mm timber post to concrete that is already poured, for example a deck, pergola or verandah post on a slab or pad footing. Choose a bolt down support when you cannot, or do not want to, cast a leg into wet concrete. For larger posts, see the \u003ca href=\"\/products\/post-support-bolt-down\"\u003ebolt down post support for 115 mm posts\u003c\/a\u003e.\u003c\/p\u003e\n\u003ch2\u003eInstallation\u003c\/h2\u003e\n\u003cp\u003eSet out the post positions, mark the holes and fix the base with masonry anchors suited to the concrete and the load. Check the support is square and the post is plumb before fixing the post through the side holes. Use galvanised or stainless steel bolts and anchors outdoors. Posts on pergolas, carports and verandahs carry uplift as well as weight, so the support, anchors and footing size must follow your plans or your engineer.\u003c\/p\u003e\n\u003ch2\u003eCommon questions\u003c\/h2\u003e\n\u003ch3\u003eWhat size post does it fit?\u003c\/h3\u003e\n\u003cp\u003eA 90 mm post. Ask us if you need a support for another post size.\u003c\/p\u003e\n\u003ch3\u003eCan I set it into wet concrete?\u003c\/h3\u003e\n\u003cp\u003eNo. This is the bolt down type, which sits on top of cured concrete. To cast a support into a footing, choose a \u003ca href=\"\/products\/post-support-split-85mm-leg\"\u003esplit leg post support\u003c\/a\u003e or a full leg post support.\u003c\/p\u003e\n\u003ch3\u003eWhat anchors do I need?\u003c\/h3\u003e\n\u003cp\u003eThat depends on the concrete and the load. Follow the anchor maker's instructions and your plans or engineer.\u003c\/p\u003e\n\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\n\u003cp\u003eYes. Pick up from our yard at 10 Lancaster Street, Ingleburn, or have it delivered across Sydney. Call (02) 4605 0215 for a delivery quote.\u003c\/p\u003e","brand":"Alpha Timber","offers":[{"title":"Default Title","offer_id":47796305920311,"sku":"704599","price":14.99,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/files\/POST-SUPPORT-BOLT-DOWN-90MM-POST-B25C.jpg?v=1766390066"},{"product_id":"post-support-center-fix-130mm","title":"Centre fix post support 130 mm (post stirrup)","description":"\u003cp\u003eThis is a 130 mm centre fix post support, a steel bracket that holds the base of a timber post on decks, pergolas, verandahs and similar structures. It is also known as a post stirrup or post anchor.\u003c\/p\u003e\u003ch2\u003eKey facts\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eType: centre fix post support (post stirrup)\u003c\/li\u003e\n\u003cli\u003eSize: 130 mm, as listed\u003c\/li\u003e\n\u003cli\u003eMaterial: steel\u003c\/li\u003e\n\u003cli\u003eSold as: each\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\u003cp\u003eSupporting the bottom of a timber post and keeping the end grain up off the concrete, where it would otherwise sit in water. A centre fix support attaches at the centre of the post's base instead of cupping the outside of the post, so less steel shows once the post is on.\u003c\/p\u003e\u003cp\u003eThe post size this support suits, and whether the 130 mm is the height or the width, are not listed online yet. Call us on (02) 4605 0215 with your post size before ordering and we will check it against the stock.\u003c\/p\u003e\u003ch2\u003eInstallation\u003c\/h2\u003e\u003cp\u003eSet out the post positions and check each support is square and plumb before the post goes on. Fix the post with galvanised or stainless steel bolts or screws outdoors. Posts on pergolas, carports and verandahs carry uplift as well as weight, so the support, its fixing to the footing and the footing size must follow your plans or your engineer.\u003c\/p\u003e\u003ch2\u003eCommon questions\u003c\/h2\u003e\u003ch3\u003eWhat size post does it fit?\u003c\/h3\u003e\u003cp\u003eThe post size is not listed online yet. Call us with your post size and we will check before you order.\u003c\/p\u003e\u003ch3\u003eIs it bolted down or cast into concrete?\u003c\/h3\u003e\u003cp\u003eThat is not listed online yet either. If you know which type you need, see our \u003ca href=\"\/products\/post-support-bolt-down-90mm-post-b25c\"\u003ebolt down post support for 90 mm posts\u003c\/a\u003e, which sits on cured concrete, or the \u003ca href=\"\/products\/post-support-split-85mm-leg\"\u003esplit leg post support\u003c\/a\u003e, which is cast into the footing.\u003c\/p\u003e\u003ch3\u003eIs it galvanised?\u003c\/h3\u003e\u003cp\u003eThe finish is not listed online yet. Ask us before using it outdoors, near the coast or against treated timber.\u003c\/p\u003e\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\u003cp\u003eYes. Pick up from our yard at 10 Lancaster Street, Ingleburn, or have it delivered across Sydney. Call (02) 4605 0215 for a delivery quote.\u003c\/p\u003e","brand":"Alpha Timber","offers":[{"title":"Default Title","offer_id":47796305953079,"sku":"23144","price":14.99,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/Post-Support-Center-Fix-130mm.jpg?v=1766390162"},{"product_id":"washers-square-galvanized-50mm-m12","title":"M12 square washer 50 x 50mm galvanised steel","description":"\u003cp\u003eGalvanised steel square washer, 50 x 50mm, with a hole to suit M12 bolts. It sits under the bolt head or nut and spreads the load over the timber, so the fixing does not crush into the wood.\u003c\/p\u003e\n\u003ch2\u003eKey facts\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eSize: 50 x 50mm square\u003c\/li\u003e\n\u003cli\u003eBolt size: M12\u003c\/li\u003e\n\u003cli\u003eMaterial: galvanised steel\u003c\/li\u003e\n\u003cli\u003eWeight: about 0.1kg each\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eBolted timber joints such as bearers to posts, beams, pergolas and decks\u003c\/li\u003e\n\u003cli\u003eUnder the heads and nuts of M12 bolts, coach screws and threaded rod\u003c\/li\u003e\n\u003cli\u003eTimber and steel construction, indoors and outdoors\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eWorking with it\u003c\/h2\u003e\n\u003cp\u003eFit a washer wherever a bolt head or nut bears on timber. Tighten until the washer beds firmly on the timber without crushing the fibres. Outdoors, use galvanised bolts and nuts with galvanised washers so the whole fixing matches. For structural connections, the bolt size, washer size and bolt layout come from AS 1684 or your engineer.\u003c\/p\u003e\n\u003ch2\u003eCommon questions\u003c\/h2\u003e\n\u003ch3\u003eWhat bolt does it fit?\u003c\/h3\u003e\n\u003cp\u003eM12 bolts, M12 threaded rod and 12mm coach screws.\u003c\/p\u003e\n\u003ch3\u003eHow many do I need?\u003c\/h3\u003e\n\u003cp\u003eUsually two for each bolt: one under the head and one under the nut, where both ends bear on timber. Where one end bears on a steel bracket, one is often enough.\u003c\/p\u003e\n\u003ch3\u003eCan it be used outdoors?\u003c\/h3\u003e\n\u003cp\u003eYes, it is galvanised and suitable for indoor and outdoor work. If your job calls for hot-dip galvanised fixings, ask us to confirm the coating before you buy.\u003c\/p\u003e\n\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\n\u003cp\u003eYes. Pick up from 10 Lancaster Street, Ingleburn, or add it to a delivery across Sydney. Phone (02) 4605 0215.\u003c\/p\u003e","brand":"Alpha Timber","offers":[{"title":"Default Title","offer_id":47796306608439,"sku":"36519","price":0.7,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/Washers-Square-Galvanized-50mm-M12.png?v=1766393888"},{"product_id":"42x42x5-4-h3-primed-dar","title":"42 x 42 H3 primed pine DAR, LOSP treated, finger jointed, 5.4 m","description":"\u003cp\u003e42 x 42 mm H3 primed pine DAR in 5.4 m lengths. It is finger-jointed radiata pine, dressed all round, H3 LOSP treated for above-ground outdoor use and factory coated in a pink primer, ready for your top coats.\u003c\/p\u003e\u003ch2\u003eKey facts\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSize: 42 x 42 mm\u003c\/li\u003e\n\u003cli\u003eLength: 5.4 m\u003c\/li\u003e\n\u003cli\u003eTimber: plantation radiata pine, finger jointed and kiln dried\u003c\/li\u003e\n\u003cli\u003eProfile: DAR (dressed all round)\u003c\/li\u003e\n\u003cli\u003eTreatment: H3 LOSP, above-ground exterior\u003c\/li\u003e\n\u003cli\u003eFinish: pink primer, ready for top coats\u003c\/li\u003e\n\u003cli\u003eWeight: about 5.2 kg per length\u003c\/li\u003e\n\u003cli\u003eSold as: single 5.4 m lengths\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\u003cp\u003eOutdoor framing, pergola and deck trims, battens, handrail supports and outdoor joinery. The H3 treatment protects against fungal decay and insect attack above ground. For other sections, see our \u003ca href=\"\/products\/42x18x5-4-h3-primed-dar\"\u003e42 x 18 H3 primed DAR\u003c\/a\u003e, \u003ca href=\"\/products\/66x42x6-0-h3-primed-dar\"\u003e66 x 42 H3 primed DAR\u003c\/a\u003e and \u003ca href=\"\/products\/90x42-h3-pre-primed-dar\"\u003e90 x 42 H3 primed DAR\u003c\/a\u003e.\u003c\/p\u003e\u003ch2\u003eWorking with it\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSeal any cut ends, notches and holes with a suitable end sealer before top coating.\u003c\/li\u003e\n\u003cli\u003eThe pink primer is an undercoat, not a finished surface. Apply two or more coats of quality exterior paint.\u003c\/li\u003e\n\u003cli\u003eH3 is for above-ground use. Keep it clear of the ground, and use H4 timber for anything in the ground.\u003c\/li\u003e\n\u003cli\u003eUse hot dipped galvanised or stainless steel fixings outdoors.\u003c\/li\u003e\n\u003cli\u003eStore lengths flat, dry and off the ground until they go up.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eFor structural members, have the size and span checked by your builder or engineer.\u003c\/p\u003e\u003ch2\u003eCommon questions\u003c\/h2\u003e\u003ch3\u003eCan it go in the ground?\u003c\/h3\u003e\u003cp\u003eNo. H3 treatment is for above-ground outdoor use. For posts or anything in contact with the ground, choose H4 treated timber.\u003c\/p\u003e\u003ch3\u003eDo I need to paint it?\u003c\/h3\u003e\u003cp\u003eYes. The pink primer is only an undercoat. Seal the cut ends, then apply two or more coats of quality exterior paint.\u003c\/p\u003e\u003ch3\u003eHow heavy is a length?\u003c\/h3\u003e\u003cp\u003eAbout 5.2 kg for a 5.4 m length, so one person can carry it.\u003c\/p\u003e\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\u003cp\u003eYes. Pick up from our yard at 10 Lancaster Street, Ingleburn, or ask us to quote delivery to your site anywhere in Sydney. Call (02) 4605 0215. The lengths are 5.4 m, so bring a vehicle that can carry them.\u003c\/p\u003e","brand":"Alpha Timber","offers":[{"title":"Default Title","offer_id":47796310212919,"sku":"201487","price":38.65,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/files\/42x42-h3-primed-dar-pink-primed-pine-alpha-timber.png?v=1795070830"},{"product_id":"66x42x6-0-h3-primed-dar","title":"66x42 H3 Primed Dar","description":"\u003cp\u003eThe \u003cstrong\u003e66x42 H3 Primed DAR\u003c\/strong\u003e is finger-jointed radiata pine, dressed all round (DAR), H3 LOSP treated and factory coated with a pink primer, ready for your top coats. H3 treatment makes it suitable for above-ground outdoor use.\u003c\/p\u003e\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eSize:\u003c\/strong\u003e 66 mm x 42 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLengths:\u003c\/strong\u003e as listed in the options above\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSpecies:\u003c\/strong\u003e plantation radiata pine, finger-jointed and kiln dried\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTreatment:\u003c\/strong\u003e H3 LOSP, above-ground exterior\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFinish:\u003c\/strong\u003e pink primer, ready for top coats\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eFeatures\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eTreated against fungal decay and insect attack for above-ground outdoor use\u003c\/li\u003e\n\u003cli\u003eFinger-jointed and kiln dried for straight, stable lengths\u003c\/li\u003e\n\u003cli\u003eSmooth dressed faces, pre-primed to save painting time\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eCommon uses\u003c\/h2\u003e\n\u003cp\u003eOutdoor framing, pergola and deck trims, battens, handrail supports and outdoor joinery. Seal any cut ends, notches and holes with a suitable end sealer before top coating, and apply two or more coats of quality exterior paint.\u003c\/p\u003e\n\u003ch2\u003ePick up or delivery\u003c\/h2\u003e\n\u003cp\u003ePick up from our yard at 10 Lancaster Street, Ingleburn, or ask us to quote delivery to your site anywhere in Sydney.\u003c\/p\u003e","brand":"Alpha Timber","offers":[{"title":"6.0m","offer_id":51439917760823,"sku":"201492","price":67.67,"currency_code":"AUD","in_stock":true},{"title":"5.4","offer_id":51439917793591,"sku":"201491","price":60.91,"currency_code":"AUD","in_stock":true},{"title":"4.8m","offer_id":51439917826359,"sku":"201490","price":54.13,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/files\/66x42-h3-primed-dar-pink-primed-pine-alpha-timber.png?v=1795070830"},{"product_id":"112x112-gl8-h3-primed-treated-post","title":"112 x 112 H3 primed GL8 glulam post, treated pine, 2.4 to 7.2 m","description":"\u003cp\u003e112 x 112 mm H3 primed GL8 post: a glue-laminated (glulam) radiata pine post, H3 LOSP treated and factory coated in a pink primer. It is used for posts above ground, such as pergola, carport, verandah and deck posts.\u003c\/p\u003e\u003ch2\u003eKey facts\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSize: 112 x 112 mm\u003c\/li\u003e\n\u003cli\u003eLengths: 2.4, 2.7, 3.0, 3.6, 4.2, 4.8, 5.4, 6.0 and 7.2 m\u003c\/li\u003e\n\u003cli\u003eGrade: GL8 glue-laminated (glulam)\u003c\/li\u003e\n\u003cli\u003eTimber: radiata pine\u003c\/li\u003e\n\u003cli\u003eTreatment: H3 LOSP, for outdoor use above ground\u003c\/li\u003e\n\u003cli\u003eFinish: pink primer, ready for top coats\u003c\/li\u003e\n\u003cli\u003eWeight: about 7.8 kg per metre (about 23 kg for 3.0 m, 47 kg for 6.0 m)\u003c\/li\u003e\n\u003cli\u003eSold as: single lengths\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\u003cp\u003ePergola, carport and verandah posts, deck posts and feature framing above ground. Glue-laminated construction keeps the post straight and stable. H3 treatment is for outdoor timber that is clear of the ground, so the post must sit on a stirrup or bracket and not in the ground. For other sizes, see \u003ca href=\"\/products\/88x88-gl8-h3-primed-treated-post\"\u003e88 x 88 GL8 H3 primed post\u003c\/a\u003e and \u003ca href=\"\/products\/135x135-gl8-h3-primed-treated-post\"\u003e135 x 135 GL8 H3 primed post\u003c\/a\u003e. For a beam to go with it, see \u003ca href=\"\/products\/180x65-h3-primed-gl10-beam\"\u003e180 x 65 H3 primed GL10 beam\u003c\/a\u003e.\u003c\/p\u003e\u003ch2\u003eWorking with it\u003c\/h2\u003e\u003cp\u003ePost sizes, heights and footings are structural: follow your plans or ask your engineer. Seal any cut ends, notches and holes with a suitable end sealer before top coating. The pink primer is an undercoat, so apply two or more coats of quality exterior paint and keep the paint maintained. Store posts flat on bearers, off the ground and under cover until they are fixed. Use hot dipped galvanised or stainless steel fixings outdoors.\u003c\/p\u003e\u003ch2\u003eCommon questions\u003c\/h2\u003e\u003ch3\u003eCan it go in the ground?\u003c\/h3\u003e\u003cp\u003eNo. H3 is for outdoor use above ground. Fix the post to a post support that holds it clear of the ground. Timber in the ground needs H4 treatment or higher.\u003c\/p\u003e\u003ch3\u003eHow heavy is it?\u003c\/h3\u003e\u003cp\u003eAbout 7.8 kg per metre. A 3.0 m post is about 23 kg and a 6.0 m post is about 47 kg.\u003c\/p\u003e\u003ch3\u003eDo I have to paint it?\u003c\/h3\u003e\u003cp\u003eYes. The pink primer is not a finish coat. Seal cut ends, then apply two or more coats of exterior paint.\u003c\/p\u003e\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\u003cp\u003eYes. Pick up from our yard at 10 Lancaster Street, Ingleburn, or have it delivered across Sydney. Lengths run to 7.2 m, so bring a vehicle that can carry them or call (02) 4605 0215 for a delivery quote.\u003c\/p\u003e","brand":"Alpha Timber","offers":[{"title":"2.4m","offer_id":51591936770359,"sku":"201547","price":129.6,"currency_code":"AUD","in_stock":false},{"title":"2.7m","offer_id":51591936803127,"sku":"201548","price":145.8,"currency_code":"AUD","in_stock":false},{"title":"3.0m","offer_id":51591936835895,"sku":"201549","price":162.0,"currency_code":"AUD","in_stock":false},{"title":"3.6m","offer_id":51591936868663,"sku":"201550","price":194.4,"currency_code":"AUD","in_stock":false},{"title":"4.2m","offer_id":51591936901431,"sku":"201551","price":226.8,"currency_code":"AUD","in_stock":true},{"title":"4.8m","offer_id":51591936934199,"sku":"201552","price":259.2,"currency_code":"AUD","in_stock":true},{"title":"5.4m","offer_id":51591936966967,"sku":"201553","price":291.6,"currency_code":"AUD","in_stock":true},{"title":"6.0m","offer_id":51591936999735,"sku":"201554","price":324.0,"currency_code":"AUD","in_stock":true},{"title":"7.2m","offer_id":51591937032503,"sku":"20198","price":388.8,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/files\/112x112-gl8-h3-primed-treated-post-pink-primed-alpha-timber.png?v=1795071683"},{"product_id":"140x65-h3-primed-gl10-beam","title":"140x65 H3 Primed GL10 Beam","description":"\u003cp\u003eThe \u003cstrong\u003e140x65 H3 Primed GL10 Beam\u003c\/strong\u003e is a GL10 glue-laminated radiata pine beam, H3 LOSP treated and factory coated with a pink primer. It is straight, stable and strong for exposed above-ground structures.\u003c\/p\u003e\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eSize:\u003c\/strong\u003e 140 mm x 65 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLengths:\u003c\/strong\u003e as listed in the options above\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGrade:\u003c\/strong\u003e GL10 glue-laminated\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTreatment:\u003c\/strong\u003e H3 LOSP, above-ground exterior\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFinish:\u003c\/strong\u003e pink primer, ready for top coats\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eFeatures\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGlue-laminated for straightness and stability over longer spans\u003c\/li\u003e\n\u003cli\u003eTreated against fungal decay and insect attack for above-ground use\u003c\/li\u003e\n\u003cli\u003ePre-primed to save painting time\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eCommon uses\u003c\/h2\u003e\n\u003cp\u003ePergola and carport beams, veranda beams, lintels and exposed framing. Size spans from the manufacturer's span tables or with your engineer. Seal any cut ends, notches and holes with a suitable end sealer before top coating, and apply two or more coats of quality exterior paint.\u003c\/p\u003e\n\u003ch2\u003ePick up or delivery\u003c\/h2\u003e\n\u003cp\u003ePick up from our yard at 10 Lancaster Street, Ingleburn, or ask us to quote delivery to your site anywhere in Sydney.\u003c\/p\u003e","brand":"Alpha Timber","offers":[{"title":"3.6m","offer_id":50199039115575,"sku":"25063","price":165.18,"currency_code":"AUD","in_stock":false},{"title":"4.8m","offer_id":47896271782199,"sku":"25064","price":220.44,"currency_code":"AUD","in_stock":false},{"title":"5.4m","offer_id":47896516067639,"sku":"25065","price":248.0,"currency_code":"AUD","in_stock":true},{"title":"6.0m","offer_id":47896516100407,"sku":"25066","price":275.55,"currency_code":"AUD","in_stock":false},{"title":"7.2m","offer_id":47896516133175,"sku":"25067","price":330.66,"currency_code":"AUD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/files\/140x65-h3-primed-gl10-glulam-beam-pink-primed-alpha-timber.png?v=1795071683"},{"product_id":"180x65-h3-primed-gl10-beam","title":"180 x 65 H3 primed GL10 glulam beam, treated pine, 3.6 to 7.2 m","description":"\u003cp\u003e180 x 65 mm H3 primed GL10 beam: a glue-laminated (glulam) radiata pine beam, H3 LOSP treated and factory coated in a pink primer. It is used for exposed beams above ground, such as pergola, carport and verandah beams.\u003c\/p\u003e\n\u003ch2\u003eKey facts\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eSize: 180 x 65 mm\u003c\/li\u003e\n\u003cli\u003eLengths: 3.6, 4.8, 5.4, 6.0 and 7.2 m\u003c\/li\u003e\n\u003cli\u003eGrade: GL10 glue-laminated (glulam)\u003c\/li\u003e\n\u003cli\u003eTimber: radiata pine\u003c\/li\u003e\n\u003cli\u003eTreatment: H3 LOSP, for outdoor use above ground\u003c\/li\u003e\n\u003cli\u003eFinish: pink primer, ready for top coats\u003c\/li\u003e\n\u003cli\u003eWeight: about 7 kg per metre (about 25 kg for 3.6 m, 51 kg for 7.2 m)\u003c\/li\u003e\n\u003cli\u003eSold as: single lengths\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\n\u003cp\u003ePergola and carport beams, verandah beams, lintels and exposed framing above ground. H3 treatment is for outdoor timber that is clear of the ground, so this beam is not for use in the ground or in contact with it.\u003c\/p\u003e\n\u003ch2\u003eWorking with it\u003c\/h2\u003e\n\u003cp\u003eSize the beam and its span from the manufacturer's span tables or with your engineer. Seal any cut ends, notches and holes with a suitable end sealer before top coating. The pink primer is an undercoat, so apply two or more coats of quality exterior paint and keep the paint maintained. Store beams flat on bearers, off the ground and under cover until they are fixed. Use hot dipped galvanised or stainless steel fixings outdoors.\u003c\/p\u003e\n\u003ch2\u003eCommon questions\u003c\/h2\u003e\n\u003ch3\u003eHow far will a 180 x 65 GL10 beam span?\u003c\/h3\u003e\n\u003cp\u003eThat depends on the load, the beam spacing and what it supports. Use the manufacturer's span tables or ask your engineer. We do not publish span figures online.\u003c\/p\u003e\n\u003ch3\u003eHow heavy is it?\u003c\/h3\u003e\n\u003cp\u003eAbout 7 kg per metre. A 6.0 m beam is about 42 kg, so plan on two people to lift and place it.\u003c\/p\u003e\n\u003ch3\u003eCan it go in the ground?\u003c\/h3\u003e\n\u003cp\u003eNo. H3 is for outdoor use above ground. Timber in the ground needs H4 treatment or higher.\u003c\/p\u003e\n\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\n\u003cp\u003eYes. Pick up from our yard at 10 Lancaster Street, Ingleburn, or have it delivered across Sydney. Lengths run to 7.2 m, so bring a vehicle that can carry them or call (02) 4605 0215 for a delivery quote.\u003c\/p\u003e","brand":"Alpha Timber","offers":[{"title":"4.8m","offer_id":47896271716663,"sku":"25069","price":273.6,"currency_code":"AUD","in_stock":false},{"title":"5.4m","offer_id":47896515936567,"sku":"25070.9","price":307.8,"currency_code":"AUD","in_stock":true},{"title":"6.0m","offer_id":47896515969335,"sku":"25071","price":342.0,"currency_code":"AUD","in_stock":true},{"title":"7.2m","offer_id":47896516002103,"sku":"25072","price":410.4,"currency_code":"AUD","in_stock":false},{"title":"3.6m","offer_id":50199183294775,"sku":"25068","price":205.2,"currency_code":"AUD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/files\/180x65-h3-primed-gl10-glulam-beam-pink-primed-alpha-timber.png?v=1795071836"},{"product_id":"90x42-h3-pre-primed-dar","title":"90x42 H3 Pre Primed DAR","description":"\u003cp\u003eThe \u003cstrong\u003e90x42 H3 Pre Primed DAR\u003c\/strong\u003e is finger-jointed radiata pine, dressed all round (DAR), H3 LOSP treated and factory coated with a pink primer, ready for your top coats. H3 treatment makes it suitable for above-ground outdoor use.\u003c\/p\u003e\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eSize:\u003c\/strong\u003e 90 mm x 42 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLengths:\u003c\/strong\u003e as listed in the options above\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSpecies:\u003c\/strong\u003e plantation radiata pine, finger-jointed and kiln dried\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTreatment:\u003c\/strong\u003e H3 LOSP, above-ground exterior\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFinish:\u003c\/strong\u003e pink primer, ready for top coats\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eFeatures\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eTreated against fungal decay and insect attack for above-ground outdoor use\u003c\/li\u003e\n\u003cli\u003eFinger-jointed and kiln dried for straight, stable lengths\u003c\/li\u003e\n\u003cli\u003eSmooth dressed faces, pre-primed to save painting time\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eCommon uses\u003c\/h2\u003e\n\u003cp\u003eOutdoor framing, pergola and deck trims, battens, handrail supports and outdoor joinery. Seal any cut ends, notches and holes with a suitable end sealer before top coating, and apply two or more coats of quality exterior paint.\u003c\/p\u003e\n\u003ch2\u003ePick up or delivery\u003c\/h2\u003e\n\u003cp\u003ePick up from our yard at 10 Lancaster Street, Ingleburn, or ask us to quote delivery to your site anywhere in Sydney.\u003c\/p\u003e","brand":"Alpha Timber","offers":[{"title":"3.6m","offer_id":50203995603255,"sku":"201494.9","price":54.49,"currency_code":"AUD","in_stock":false},{"title":"4.2m","offer_id":50203996717367,"sku":"37181","price":63.58,"currency_code":"AUD","in_stock":true},{"title":"4.8m","offer_id":47896271618359,"sku":"201495","price":72.66,"currency_code":"AUD","in_stock":true},{"title":"5.4m","offer_id":47896515674423,"sku":"201496","price":81.74,"currency_code":"AUD","in_stock":true},{"title":"6.0m","offer_id":47896515707191,"sku":"201497","price":90.82,"currency_code":"AUD","in_stock":true},{"title":"7.2m","offer_id":50204004516151,"sku":"NC0004","price":108.98,"currency_code":"AUD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/files\/90x42-h3-pre-primed-dar-pink-primed-pine-alpha-timber.png?v=1795071416"},{"product_id":"140x45-h3-treated-pine","title":"140 x 45 H3 treated pine, MGP10 LOSP, 3.6 to 6.0 m","description":"\u003cp\u003e140 x 45 mm H3 LOSP treated pine, graded MGP10 and kiln dried. It is structural framing timber for outdoor work above the ground, such as pergola beams, rafters and external frames.\u003c\/p\u003e\u003ch2\u003eKey facts\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSize: 140 x 45 mm\u003c\/li\u003e\n\u003cli\u003eGrade: MGP10 (machine graded pine)\u003c\/li\u003e\n\u003cli\u003eTreatment: H3 LOSP (light organic solvent preservative), for outdoor use above ground\u003c\/li\u003e\n\u003cli\u003eSeasoning: kiln dried\u003c\/li\u003e\n\u003cli\u003eLengths: 3.6 m, 4.8 m and 6.0 m\u003c\/li\u003e\n\u003cli\u003eWeight: about 3.5 kg per metre\u003c\/li\u003e\n\u003cli\u003eSold as: single lengths\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\u003cp\u003ePergola beams and rafters, deck joists and bearers above ground, external framing, landscaping structures and other outdoor projects that stay clear of the ground. The H3 treatment protects the timber against decay, termites and borers where it gets wet from time to time. For frames that stay dry inside the building, see \u003ca href=\"\/products\/140-x-45-h2-mgp10-pine\"\u003e140 x 45 H2 MGP10 pine\u003c\/a\u003e. For a smaller outdoor section, see \u003ca href=\"\/products\/90x45-h3-treated-pine\"\u003e90 x 45 H3 treated pine\u003c\/a\u003e.\u003c\/p\u003e\u003ch2\u003eWorking with it\u003c\/h2\u003e\u003cp\u003eIt cuts, drills and fixes like untreated pine. Seal every cut end, notch and drilled hole with a cut-end preservative, because cutting exposes untreated timber. Use hot dipped galvanised or stainless steel fixings outdoors. A paint or stain coat helps it last longer in the weather. Spans and member sizes are structural: check the span tables on your plans or ask your engineer.\u003c\/p\u003e\u003ch2\u003eCommon questions\u003c\/h2\u003e\u003ch3\u003eCan H3 treated pine go in the ground?\u003c\/h3\u003e\u003cp\u003eNo. H3 is for outdoor use above ground. Timber set in the ground or sitting on it needs H4 treatment or higher.\u003c\/p\u003e\u003ch3\u003eHow heavy is a length?\u003c\/h3\u003e\u003cp\u003eAbout 3.5 kg per metre. That is about 12.5 kg for 3.6 m, 16.6 kg for 4.8 m and 20.8 kg for 6.0 m.\u003c\/p\u003e\u003ch3\u003eDo I need to seal cut ends?\u003c\/h3\u003e\u003cp\u003eYes. Brush a cut-end preservative onto every cut, notch and hole before you fix the timber in place.\u003c\/p\u003e\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\u003cp\u003eYes. Pick up from our yard at 10 Lancaster Street, Ingleburn, or we can deliver across Sydney, including 6.0 m lengths.\u003c\/p\u003e","brand":"Alpha Timber","offers":[{"title":"3.6m","offer_id":47896271388983,"sku":"200150.3","price":45.5,"currency_code":"AUD","in_stock":true},{"title":"4.8m","offer_id":47896514953527,"sku":"200150.5","price":60.67,"currency_code":"AUD","in_stock":true},{"title":"6.0m","offer_id":47896515019063,"sku":"200150.7","price":75.84,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/files\/140x45-h3-treated-pine-mgp10-outdoor-structural-alpha-timber.png?v=1795061161"},{"product_id":"190x45-h3-treated-pine","title":"190 x 45 H3 treated pine, MGP10 LOSP, 3.6 to 6.0 m","description":"\u003cp\u003e190 x 45 mm H3 LOSP treated pine, graded MGP10 and kiln dried. It is structural timber for outdoor work above the ground, such as pergola beams, bearers and stair stringers.\u003c\/p\u003e\u003ch2\u003eKey facts\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSize: 190 x 45 mm\u003c\/li\u003e\n\u003cli\u003eGrade: MGP10 (machine graded pine)\u003c\/li\u003e\n\u003cli\u003eTreatment: H3 LOSP (light organic solvent preservative), for outdoor use above ground\u003c\/li\u003e\n\u003cli\u003eSeasoning: kiln dried\u003c\/li\u003e\n\u003cli\u003eLengths: 3.6 m, 4.2 m, 4.8 m, 5.4 m and 6.0 m\u003c\/li\u003e\n\u003cli\u003eWeight: about 4.7 kg per metre\u003c\/li\u003e\n\u003cli\u003eSold as: single lengths\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\u003cp\u003ePergola beams, bearers, stair stringers, external framing and other outdoor projects that stay clear of the ground. The H3 treatment protects the timber against decay, termites and borers where it gets wet from time to time. For frames that stay dry inside the building, see \u003ca href=\"\/products\/190-x-45-h2-mgp10-pine\"\u003e190 x 45 H2 MGP10 pine\u003c\/a\u003e. For smaller outdoor sections, see \u003ca href=\"\/products\/140x45-h3-treated-pine\"\u003e140 x 45 H3 treated pine\u003c\/a\u003e and \u003ca href=\"\/products\/90x45-h3-treated-pine\"\u003e90 x 45 H3 treated pine\u003c\/a\u003e.\u003c\/p\u003e\u003ch2\u003eWorking with it\u003c\/h2\u003e\u003cp\u003eIt cuts, drills and fixes like untreated pine. Seal every cut end, notch and drilled hole with a cut-end preservative, because cutting exposes untreated timber. Use hot dipped galvanised or stainless steel fixings outdoors. A paint or stain coat helps it last longer in the weather. Spans and member sizes are structural: check the span tables on your plans or ask your engineer.\u003c\/p\u003e\u003ch2\u003eCommon questions\u003c\/h2\u003e\u003ch3\u003eCan H3 treated pine go in the ground?\u003c\/h3\u003e\u003cp\u003eNo. H3 is for outdoor use above ground. Timber set in the ground or sitting on it needs H4 treatment or higher.\u003c\/p\u003e\u003ch3\u003eHow heavy is a length?\u003c\/h3\u003e\u003cp\u003eAbout 4.7 kg per metre. That is about 17 kg for 3.6 m, 22.6 kg for 4.8 m and 28 kg for 6.0 m.\u003c\/p\u003e\u003ch3\u003eDo I need to seal cut ends?\u003c\/h3\u003e\u003cp\u003eYes. Brush a cut-end preservative onto every cut, notch and hole before you fix the timber in place.\u003c\/p\u003e\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\u003cp\u003eYes. Pick up from our yard at 10 Lancaster Street, Ingleburn, or we can deliver across Sydney, including 6.0 m lengths.\u003c\/p\u003e","brand":"Alpha Timber","offers":[{"title":"3.6m","offer_id":47896271356215,"sku":"200151.6","price":53.96,"currency_code":"AUD","in_stock":true},{"title":"4.2m","offer_id":50446539161911,"sku":"200151","price":62.96,"currency_code":"AUD","in_stock":true},{"title":"4.8m","offer_id":47896514855223,"sku":"200152","price":71.95,"currency_code":"AUD","in_stock":true},{"title":"5.4m","offer_id":50446540177719,"sku":"200153","price":80.95,"currency_code":"AUD","in_stock":true},{"title":"6.0m","offer_id":47896514920759,"sku":"200153.2","price":89.94,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/files\/190x45-h3-treated-pine-outdoor-structural-timber-alpha-timber.png?v=1795061161"},{"product_id":"135x135-gl8-h3-primed-treated-post","title":"135 x 135 H3 primed GL8 glulam post, treated pine, 2.4 to 6.0 m","description":"\u003cp\u003e135 x 135 mm H3 primed GL8 post: a glue-laminated (glulam) radiata pine post, H3 LOSP treated and factory coated in a pink primer. It is used for posts above ground, such as pergola, carport, verandah and deck posts.\u003c\/p\u003e\u003ch2\u003eKey facts\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSize: 135 x 135 mm\u003c\/li\u003e\n\u003cli\u003eLengths: 2.4, 2.7, 3.0, 3.6, 4.2, 4.8, 5.4 and 6.0 m\u003c\/li\u003e\n\u003cli\u003eGrade: GL8 glue-laminated (glulam)\u003c\/li\u003e\n\u003cli\u003eTimber: radiata pine\u003c\/li\u003e\n\u003cli\u003eTreatment: H3 LOSP, for outdoor use above ground\u003c\/li\u003e\n\u003cli\u003eFinish: pink primer, ready for top coats\u003c\/li\u003e\n\u003cli\u003eWeight: about 11.3 kg per metre (about 34 kg for 3.0 m, 68 kg for 6.0 m)\u003c\/li\u003e\n\u003cli\u003eSold as: single lengths\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\u003cp\u003ePergola, carport and verandah posts, deck posts and feature framing above ground. Glue-laminated construction keeps the post straight and stable. H3 treatment is for outdoor timber that is clear of the ground, so the post must sit on a stirrup or bracket and not in the ground. For smaller posts, see \u003ca href=\"\/products\/88x88-gl8-h3-primed-treated-post\"\u003e88 x 88 GL8 H3 primed post\u003c\/a\u003e and \u003ca href=\"\/products\/112x112-gl8-h3-primed-treated-post\"\u003e112 x 112 GL8 H3 primed post\u003c\/a\u003e. For a beam to go with it, see \u003ca href=\"\/products\/180x65-h3-primed-gl10-beam\"\u003e180 x 65 H3 primed GL10 beam\u003c\/a\u003e.\u003c\/p\u003e\u003ch2\u003eWorking with it\u003c\/h2\u003e\u003cp\u003ePost sizes, heights and footings are structural: follow your plans or ask your engineer. Seal any cut ends, notches and holes with a suitable end sealer before top coating. The pink primer is an undercoat, so apply two or more coats of quality exterior paint and keep the paint maintained. Store posts flat on bearers, off the ground and under cover until they are fixed. Use hot dipped galvanised or stainless steel fixings outdoors.\u003c\/p\u003e\u003ch2\u003eCommon questions\u003c\/h2\u003e\u003ch3\u003eCan it go in the ground?\u003c\/h3\u003e\u003cp\u003eNo. H3 is for outdoor use above ground. Fix the post to a post support that holds it clear of the ground. Timber in the ground needs H4 treatment or higher.\u003c\/p\u003e\u003ch3\u003eHow heavy is it?\u003c\/h3\u003e\u003cp\u003eAbout 11.3 kg per metre. A 3.0 m post is about 34 kg and a 6.0 m post is about 68 kg, so plan a two-person lift for the longer lengths.\u003c\/p\u003e\u003ch3\u003eDo I have to paint it?\u003c\/h3\u003e\u003cp\u003eYes. The pink primer is not a finish coat. Seal cut ends, then apply two or more coats of exterior paint.\u003c\/p\u003e\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\u003cp\u003eYes. Pick up from our yard at 10 Lancaster Street, Ingleburn, or have it delivered across Sydney. Lengths run to 6.0 m, so bring a vehicle that can carry them or call (02) 4605 0215 for a delivery quote.\u003c\/p\u003e","brand":"Alpha Timber","offers":[{"title":"2.4m","offer_id":50198802268471,"sku":"201565.9","price":177.6,"currency_code":"AUD","in_stock":true},{"title":"2.7m","offer_id":47896271061303,"sku":"201566","price":199.8,"currency_code":"AUD","in_stock":true},{"title":"3.0m","offer_id":47896514396471,"sku":"201567","price":222.0,"currency_code":"AUD","in_stock":false},{"title":"3.6m","offer_id":47896514429239,"sku":"201568","price":266.4,"currency_code":"AUD","in_stock":true},{"title":"4.2m","offer_id":50198805315895,"sku":"201543","price":310.8,"currency_code":"AUD","in_stock":true},{"title":"4.8m","offer_id":47896514462007,"sku":"201570","price":355.2,"currency_code":"AUD","in_stock":true},{"title":"5.4m","offer_id":47896514494775,"sku":"201571","price":399.6,"currency_code":"AUD","in_stock":true},{"title":"6.0m","offer_id":47896514527543,"sku":"201572","price":444.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/files\/135x135-gl8-h3-primed-treated-post-pink-primed-alpha-timber.png?v=1795071683"}],"url":"https:\/\/alphatimber.com.au\/collections\/pergola.oembed","provider":"ALPHA TIMBER","version":"1.0","type":"link"}