{"title":"James Hardie","description":"\u003cp\u003eJames Hardie fibre cement cladding, weatherboards, sheets and trims at Alpha Timber, 10 Lancaster Street, Ingleburn. The range here includes Axon, FineTex, Linea, HardiePlank and Easylap cladding, Villaboard lining, and the matching aluminium corners, flashings and sealant. Pick up from the store or have it delivered across Sydney.\u003c\/p\u003e","products":[{"product_id":"james-hardie-villaboard-6-0mm","title":"James Hardie Villaboard lining 6mm, 2400 to 3000 x 1200mm","description":"\u003cp\u003eJames Hardie Villaboard Lining is a 6 mm sanded fibre cement sheet with recessed long edges for flush jointing, sold here in 2400 x 1200, 2700 x 1200 and 3000 x 1200 mm sheets. It is an internal wall and ceiling lining for bathrooms, laundries, kitchens and high traffic areas, and takes tiles or paint.\u003c\/p\u003e\u003ch2\u003eKey facts\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eThickness: 6 mm\u003c\/li\u003e\n\u003cli\u003eSheet sizes: 2400 x 1200, 2700 x 1200 and 3000 x 1200 mm\u003c\/li\u003e\n\u003cli\u003eMaterial: sanded fibre cement, long edges recessed\u003c\/li\u003e\n\u003cli\u003eCoverage: 2.88 m², 3.24 m² and 3.6 m² per sheet\u003c\/li\u003e\n\u003cli\u003eWeight: James Hardie lists 8.3 kg per square metre, so about 24 kg, 27 kg and 30 kg per sheet\u003c\/li\u003e\n\u003cli\u003eUse: internal walls and ceilings. James Hardie says it is not suitable as an external wall cladding\u003c\/li\u003e\n\u003cli\u003eSold as: single sheets\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eBathroom, laundry and kitchen walls as a base for tiles\u003c\/li\u003e\n\u003cli\u003eCeilings and walls where a tougher lining than plasterboard is needed\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eJames Hardie lists the 6 mm sheet for residential work.\u003c\/p\u003e\u003ch2\u003eInstallation\u003c\/h2\u003e\u003cp\u003eThese points come from James Hardie's Villaboard Lining installation guide (April 2023), attached to this page.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eTimber frames: 30 x 2.8 mm galvanised fibre cement nails. Steel frames: 25 mm Hardie Drive screws. Drive fasteners flush.\u003c\/li\u003e\n\u003cli\u003eTiled walls are fixed with fasteners only. Ceilings must never be fixed with adhesive alone.\u003c\/li\u003e\n\u003cli\u003eSet the recessed joints with Hardie Base Coat and perforated paper tape. Add Hardie Top Coat where the wall will be painted.\u003c\/li\u003e\n\u003cli\u003eFix tiles with a flexible tile adhesive. Do not tile ceilings, or walls over 3 m high. The guide's Table 9 gives the tile thickness and weight limits.\u003c\/li\u003e\n\u003cli\u003eIn wet areas, waterproofing must meet the relevant codes and standards. See James Hardie's Wet Area Construction application guide, also attached.\u003c\/li\u003e\n\u003cli\u003eCut by score and snap with a knife, a hand guillotine or fibreshears. Never use a power saw indoors, a grinder, or a dry broom on the dust. The dust contains silica, so wear a respirator.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eStud, ceiling batten and fastener spacing are shown in the guide. Follow the current guide for the full detail.\u003c\/p\u003e\u003ch2\u003eCommon questions\u003c\/h2\u003e\u003ch3\u003eHow heavy is a sheet of 6 mm Villaboard?\u003c\/h3\u003e\u003cp\u003eJames Hardie lists 8.3 kg per square metre. That is about 24 kg for a 2400 x 1200 sheet, 27 kg for 2700 x 1200 and 30 kg for 3000 x 1200.\u003c\/p\u003e\u003ch3\u003eCan I tile straight onto Villaboard?\u003c\/h3\u003e\u003cp\u003eYes. James Hardie says it creates a suitable surface for tiles or paint. Use a flexible tile adhesive, and in wet areas waterproof first as the codes require.\u003c\/p\u003e\u003ch3\u003eCan I use Villaboard outside?\u003c\/h3\u003e\u003cp\u003eNo. James Hardie says Villaboard Lining is not suitable as an external wall cladding. Ask us about exterior fibre cement sheets.\u003c\/p\u003e\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\u003cp\u003eYes. Pick up from our yard at 10 Lancaster Street, Ingleburn (Mon–Fri 6am–4pm, Sat 6am–3pm), or have it delivered across Greater Sydney. Call (02) 4605 0215 for a delivery price.\u003c\/p\u003e","brand":"Alpha Timber","offers":[{"title":"2400x1200mmx6.0mm","offer_id":47896283480375,"sku":"400362","price":46.49,"currency_code":"AUD","in_stock":true},{"title":"2700x1200mmx6.0mm","offer_id":47896539398455,"sku":"400361","price":56.6,"currency_code":"AUD","in_stock":true},{"title":"3000x1200mmx6.0mm","offer_id":47896539431223,"sku":"400360","price":62.89,"currency_code":"AUD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/files\/james-hardie-villaboard-6mm-fibre-cement-alpha-timber.png?v=1795073376"},{"product_id":"james-hardie-finetex-cladding","title":"James Hardie Fine Texture cladding 8.5mm fibre cement panel","description":"\u003cp\u003eHardie Fine Texture cladding (also sold as FineTex) is an 8.5 mm James Hardie fibre cement panel with a fine sand texture embedded in the face and a shiplap V-joint on the long edges. It is fixed vertically to framed walls and painted on site to give a rendered look without rendering.\u003c\/p\u003e\n\u003ch2\u003eKey facts\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eThickness: 8.5 mm\u003c\/li\u003e\n\u003cli\u003eSizes: 2440 x 1200 mm, 2750 x 1200 mm, 3000 x 1200 mm and 3600 x 1200 mm\u003c\/li\u003e\n\u003cli\u003eMaterial: fibre cement with an embedded fine texture, pre-sealed\u003c\/li\u003e\n\u003cli\u003eEdges: shiplap V-joint on the long edges\u003c\/li\u003e\n\u003cli\u003eWeight (James Hardie, approximate): 38 kg (2440), 43 kg (2750), 47 kg (3000), 56 kg (3600). About 13 kg per m²\u003c\/li\u003e\n\u003cli\u003eCoverage per panel: 2.93 m², 3.3 m², 3.6 m² and 4.32 m²\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eThe size shown as 2745 x 1200 mm in the size list is James Hardie's 2750 x 1200 mm panel.\u003c\/p\u003e\n\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\n\u003cp\u003eExternal wall cladding on residential buildings, over a seasoned timber or light gauge steel frame. James Hardie's guide covers direct fixing to timber frames, or fixing over cavity battens on timber or steel frames.\u003c\/p\u003e\n\u003ch2\u003eInstallation\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003ePanels run vertically. Maximum stud or batten spacing is 600 mm for wind classes N1 to N4, 450 mm for N5 and 300 mm for N6.\u003c\/li\u003e\n\u003cli\u003eRun a bead of joint sealant on the shiplap edge and use foam back sealing tape behind vertical joins, as shown in the guide.\u003c\/li\u003e\n\u003cli\u003eKeep at least 150 mm clearance to the ground and 50 mm from roofs, decks, paths and driveways.\u003c\/li\u003e\n\u003cli\u003eJames Hardie says no primer is needed. Finish with an exterior acrylic paint.\u003c\/li\u003e\n\u003cli\u003eFibre cement dust contains silica. Cut with a dust-reducing saw and vacuum extraction, wear a P2 respirator, and never use a grinder or dry sweep the dust.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eFollow the current James Hardie installation guide for framing, fixings and weatherproofing. For bushfire zones, fire rated walls or anything structural, check the James Hardie documents and your building designer or engineer.\u003c\/p\u003e\n\u003ch2\u003eCommon questions\u003c\/h2\u003e\n\u003ch3\u003eIs Fine Texture the same as FineTex?\u003c\/h3\u003e\n\u003cp\u003eYes. FineTex is the short name used in our system for Hardie Fine Texture cladding.\u003c\/p\u003e\n\u003ch3\u003eHow heavy is a panel?\u003c\/h3\u003e\n\u003cp\u003eJames Hardie lists about 38 kg for a 2440 x 1200 panel, 43 kg for 2750, 47 kg for 3000 and 56 kg for 3600. Plan on two people to carry and fix them.\u003c\/p\u003e\n\u003ch3\u003eDoes it need rendering or priming?\u003c\/h3\u003e\n\u003cp\u003eNo. The texture is already in the face of the panel and James Hardie says no primer is needed. It is painted on site with exterior acrylic paint.\u003c\/p\u003e\n\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\n\u003cp\u003eYes. Pick up from our yard at 10 Lancaster Street, Ingleburn, or ask us about delivery across Sydney. Call (02) 4605 0215 to check stock on the size you need.\u003c\/p\u003e","brand":"Alpha Timber","offers":[{"title":"2440x1200mm","offer_id":50222019969335,"sku":"405252","price":133.31,"currency_code":"AUD","in_stock":true},{"title":"2745x1200mm","offer_id":47896282136887,"sku":"405255","price":149.54,"currency_code":"AUD","in_stock":true},{"title":"3000x1200mm","offer_id":47896536351031,"sku":"405253","price":163.7,"currency_code":"AUD","in_stock":true},{"title":"3600x1200mm","offer_id":47896536383799,"sku":"405254","price":196.37,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/James-Hardie-FineTex-Cladding.png?v=1766108968"},{"product_id":"james-hardie-axon-cladding","title":"James Hardie Axon cladding 9mm, 133 and 400 groove panels","description":"\u003cp\u003eJames Hardie Axon cladding is a 9 mm pre-primed fibre cement panel with vertical grooves that give the look of vertical joint timber. The number in the name is the groove spacing: Axon 133 has grooves 133 mm apart and Axon 400 has grooves 400 mm apart.\u003c\/p\u003e\n\u003ch2\u003eKey facts\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eThickness: 9 mm\u003c\/li\u003e\n\u003cli\u003ePanel width: 1200 mm\u003c\/li\u003e\n\u003cli\u003eAxon 133 Smooth: 2450, 2750, 3000 and 3600 mm long\u003c\/li\u003e\n\u003cli\u003eAxon 133 Grained (timber-look texture): 3000 mm long\u003c\/li\u003e\n\u003cli\u003eAxon 400 Smooth: 2450, 2750 and 3000 mm long\u003c\/li\u003e\n\u003cli\u003eMaterial: fibre cement, pre-primed\u003c\/li\u003e\n\u003cli\u003eEdges: stepped shiplap joint on the long edges\u003c\/li\u003e\n\u003cli\u003eWeight (James Hardie): 38.1 kg (2450), 42.8 kg (2750), 46.7 kg (3000), 56 kg (3600)\u003c\/li\u003e\n\u003cli\u003eCoverage per panel: 2.94 m² (2450), 3.3 m² (2750), 3.6 m² (3000), 4.32 m² (3600)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\n\u003cp\u003eExternal wall cladding on houses, fixed over a seasoned timber or light gauge steel wall frame. It can be fixed direct to the frame or over cavity battens. James Hardie also publishes a technical supplement for using Axon on interior walls.\u003c\/p\u003e\n\u003ch2\u003eInstallation\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003ePanels run vertically. Maximum stud or batten spacing is 600 mm for wind classes N1 to N4, 450 mm for N5 and 300 mm for N6.\u003c\/li\u003e\n\u003cli\u003eRun a bead of joint sealant on the shiplap edge and use foam back sealing tape under vertical joints, as shown in the guide.\u003c\/li\u003e\n\u003cli\u003eKeep at least 150 mm clearance to the ground and 50 mm from roofs, decks, paths and driveways.\u003c\/li\u003e\n\u003cli\u003ePaint within 3 months of fixing, or within 7 days if the site is within 1 km of the coast.\u003c\/li\u003e\n\u003cli\u003eFibre cement dust contains silica. Cut with a dust-reducing saw and vacuum extraction, wear a P2 respirator, and never use a grinder, dry sweep the dust or run a power saw indoors.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eFollow the current James Hardie Axon Cladding installation guide for framing, fixings and weatherproofing. For bracing, fire rated walls or anything structural, check with your building designer or engineer.\u003c\/p\u003e\n\u003ch2\u003eCommon questions\u003c\/h2\u003e\n\u003ch3\u003eWhat is the difference between Axon 133 and Axon 400?\u003c\/h3\u003e\n\u003cp\u003eThe groove spacing. Axon 133 has a groove every 133 mm for a narrow board look. Axon 400 has a groove every 400 mm for a wide board look. Axon 133 also comes in a Grained finish with a timber-look texture.\u003c\/p\u003e\n\u003ch3\u003eHow heavy is an Axon panel?\u003c\/h3\u003e\n\u003cp\u003eJames Hardie lists 38.1 kg for a 2450 mm panel, 42.8 kg for 2750 mm, 46.7 kg for 3000 mm and 56 kg for 3600 mm. Plan on two people to carry and fix them.\u003c\/p\u003e\n\u003ch3\u003eDoes Axon need painting?\u003c\/h3\u003e\n\u003cp\u003eYes. The panels come pre-primed and are painted on site. James Hardie says to paint within 3 months of fixing, or within 7 days near the coast.\u003c\/p\u003e\n\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\n\u003cp\u003eYes. Pick up from our yard at 10 Lancaster Street, Ingleburn, or ask us about delivery across Sydney. Call (02) 4605 0215 to check stock on the size and finish you need.\u003c\/p\u003e","brand":"Alpha Timber","offers":[{"title":"2450x1200x133mm Smooth","offer_id":47896282104119,"sku":"403931","price":156.0,"currency_code":"AUD","in_stock":true},{"title":"2750x1200x133mm Smooth","offer_id":47896536187191,"sku":"403932","price":168.3,"currency_code":"AUD","in_stock":true},{"title":"3000x1200x133mm Smooth","offer_id":47896536252727,"sku":"403933","price":183.4,"currency_code":"AUD","in_stock":false},{"title":"3600x1200x133mm Smooth","offer_id":47896536285495,"sku":"404979","price":223.82,"currency_code":"AUD","in_stock":true},{"title":"3000x1200x133mm Grained","offer_id":50221986971959,"sku":"404512","price":207.0,"currency_code":"AUD","in_stock":false},{"title":"2450x1200x400mm Smooth","offer_id":47896536154423,"sku":"404417","price":155.0,"currency_code":"AUD","in_stock":true},{"title":"2750x1200x400mm Smooth","offer_id":47896536219959,"sku":"404418","price":168.3,"currency_code":"AUD","in_stock":false},{"title":"3000x1200x400mm Smooth","offer_id":50221741965623,"sku":"404419","price":186.5,"currency_code":"AUD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/James-Hardie-Axon-Cladding.png?v=1766107217"},{"product_id":"james-hardie-finetex-9mm-aluminium-rec-horizontal-flashing-3-0m","title":"James Hardie 9mm aluminium horizontal express jointer 3000mm","description":"\u003cp\u003eThe Hardie 9mm aluminium horizontal express jointer is a 3000 mm aluminium jointer for the horizontal joints in James Hardie panel cladding. James Hardie describes it as a horizontal jointer that creates a 6 mm horizontal shadow line while concealing the edge of the bottom panels.\u003c\/p\u003e\u003ch2\u003eKey facts\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eBrand: James Hardie, product code 306104\u003c\/li\u003e\n\u003cli\u003eLength: 3000 mm (3.0 m)\u003c\/li\u003e\n\u003cli\u003eMaterial: aluminium\u003c\/li\u003e\n\u003cli\u003eShadow line: 6 mm, horizontal\u003c\/li\u003e\n\u003cli\u003eListed for: Hardie Fine Texture Cladding and Hardie Brushed Concrete Cladding\u003c\/li\u003e\n\u003cli\u003eJoining: James Hardie lists a matching connector (code 306110) for joining lengths\u003c\/li\u003e\n\u003cli\u003eSold as: single length\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\u003cp\u003eHorizontal joints where one row of panels sits above another, on walls clad in \u003ca href=\"\/products\/james-hardie-finetex-cladding\"\u003eHardie Fine Texture cladding\u003c\/a\u003e (FineTex) or Hardie Brushed Concrete cladding. It is a cladding accessory, not a roof flashing. James Hardie also makes a separate recessed horizontal jointer (code 306190). This listing is the express jointer, code 306104. For the other edges of the wall, see the \u003ca href=\"\/products\/james-hardie-finetex-9mm-aluminium-rec-base-trim-flashing-3-0m\"\u003e9mm base trim\u003c\/a\u003e and the \u003ca href=\"\/products\/james-hardie-finetex-9mm-aluminium-external-slimline-corner-3-0m\"\u003e9mm external slimline corner\u003c\/a\u003e.\u003c\/p\u003e\u003ch2\u003eInstallation\u003c\/h2\u003e\u003cp\u003eFollow the Hardie Fine Texture Cladding and Hardie Brushed Concrete Cladding installation guide (September 2026), listed under this product's documents. Its steps say to apply a continuous 4 mm bead of Hardie Joint Sealant to the edge of the panel, then install the horizontal jointer. Where slimline corners are used, the horizontal jointer must be cut at 45 degrees. Use the guide's direct fix or cavity fix details for fixing and for the panel above.\u003c\/p\u003e\u003ch2\u003eCommon questions\u003c\/h2\u003e\u003ch3\u003eWhich cladding does it suit?\u003c\/h3\u003e\u003cp\u003eIt is listed in James Hardie's installation guide for Hardie Fine Texture Cladding and Hardie Brushed Concrete Cladding.\u003c\/p\u003e\u003ch3\u003eHow many lengths do I need?\u003c\/h3\u003e\u003cp\u003eJames Hardie's rule is the total length of horizontal joints divided by 3000 mm. Round up, and allow extra for offcuts at corners.\u003c\/p\u003e\u003ch3\u003eHow are lengths joined?\u003c\/h3\u003e\u003cp\u003eJames Hardie lists a horizontal express connector (code 306110) for joining lengths. Call (02) 4605 0215 to check stock of the connector.\u003c\/p\u003e\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\u003cp\u003eYes. Pick up from our yard at 10 Lancaster Street, Ingleburn, or have it delivered across Sydney with the rest of your order. Call (02) 4605 0215 to check stock.\u003c\/p\u003e","brand":"Alpha Timber","offers":[{"title":"Default Title","offer_id":47748426498359,"sku":"306104","price":38.1,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/FineTex-9mm-Alu-Rec-Horizontal-Flashing-3.0m.png?v=1766108804"},{"product_id":"james-hardie-finetex-9mm-aluminium-rec-base-trim-flashing-3-0m","title":"James Hardie 9mm aluminium base trim 3000mm","description":"\u003cp\u003eThe Hardie 9mm aluminium base trim is a 3000 mm aluminium trim that finishes the bottom edge of James Hardie panel cladding. It suits 8.5 to 9 mm thick cladding panels and creates a shadow line over a slab edge or a balcony edge.\u003c\/p\u003e\u003ch2\u003eKey facts\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eBrand: James Hardie, product code 306105\u003c\/li\u003e\n\u003cli\u003eLength: 3000 mm (3.0 m)\u003c\/li\u003e\n\u003cli\u003eMaterial: aluminium\u003c\/li\u003e\n\u003cli\u003eSuits cladding panels 8.5 to 9 mm thick\u003c\/li\u003e\n\u003cli\u003eFinish: ready to paint after installation\u003c\/li\u003e\n\u003cli\u003eJoining: James Hardie lists a matching base trim connector (code 306111) for joining lengths\u003c\/li\u003e\n\u003cli\u003eSold as: single length\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\u003cp\u003eThe bottom edge of walls clad in 8.5 to 9 mm James Hardie panels, such as \u003ca href=\"\/products\/james-hardie-finetex-cladding\"\u003eHardie Fine Texture cladding\u003c\/a\u003e (FineTex) and Hardie Brushed Concrete cladding. James Hardie's guide describes it as a trim to cover slab edges, or a detail under balconies and cantilevers, and says the base trim option may hide a poor quality slab edge. For the corners, see the \u003ca href=\"\/products\/james-hardie-finetex-9mm-aluminium-external-slimline-corner-3-0m\"\u003e9mm external slimline corner\u003c\/a\u003e and the \u003ca href=\"\/products\/james-hardie-external-corner-3-0m\"\u003e9mm external square corner\u003c\/a\u003e.\u003c\/p\u003e\u003ch2\u003eInstallation\u003c\/h2\u003e\u003cp\u003eFollow the Hardie Fine Texture Cladding and Hardie Brushed Concrete Cladding installation guide (September 2026), listed under this product's documents. The corner accessories go on first, and the base trim then slides into them. Where slimline corners are used, James Hardie's cavity fix steps say to cut the base flashing at 45 degrees. Keep the cladding at least 150 mm clear of the ground and 50 mm clear of roofs, decks, paths, steps and driveways. Where the exposed slab edge is part of the termite barrier, at least 75 mm of the slab edge must stay visible. The trim is ready to paint, so paint it with the wall.\u003c\/p\u003e\u003ch2\u003eCommon questions\u003c\/h2\u003e\u003ch3\u003eWhich cladding does it suit?\u003c\/h3\u003e\u003cp\u003eCladding panels 8.5 to 9 mm thick. It is listed in James Hardie's installation guide for Hardie Fine Texture Cladding and Hardie Brushed Concrete Cladding.\u003c\/p\u003e\u003ch3\u003eHow many lengths do I need?\u003c\/h3\u003e\u003cp\u003eEach length is 3000 mm. Measure the run along the bottom of the clad walls, divide by 3.0 and round up. Allow extra for offcuts at corners.\u003c\/p\u003e\u003ch3\u003eHow are lengths joined?\u003c\/h3\u003e\u003cp\u003eJames Hardie lists a base trim connector (code 306111) for joining lengths. Call (02) 4605 0215 to check stock of the connector.\u003c\/p\u003e\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\u003cp\u003eYes. Pick up from our yard at 10 Lancaster Street, Ingleburn, or have it delivered across Sydney with the rest of your order. Call (02) 4605 0215 to check stock.\u003c\/p\u003e","brand":"Alpha Timber","offers":[{"title":"Default Title","offer_id":47748426236215,"sku":"306105","price":59.51,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/FineTex-9mm-Alu-Rec-Base-Trim-Flashing-3.0m.png?v=1766108634"},{"product_id":"james-hardie-finetex-9mm-aluminium-external-slimline-corner-3-0m","title":"James Hardie 9mm aluminium external slimline corner 3000mm","description":"\u003cp\u003eThe Hardie 9mm aluminium external slimline corner is a 3000 mm aluminium trim that finishes the outside corners of James Hardie panel cladding with a sharp, narrow edge. It suits 8.5 mm thick cladding panels and covers just 3.5 mm of each panel edge.\u003c\/p\u003e\u003ch2\u003eKey facts\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eBrand: James Hardie, product code 306102\u003c\/li\u003e\n\u003cli\u003eLength: 3000 mm (3.0 m)\u003c\/li\u003e\n\u003cli\u003eMaterial: aluminium\u003c\/li\u003e\n\u003cli\u003eSuits cladding panels 8.5 mm thick\u003c\/li\u003e\n\u003cli\u003eCoverage: 3.5 mm\u003c\/li\u003e\n\u003cli\u003eCompatible cladding: Hardie Fine Texture Cladding and Hardie Brushed Concrete Cladding\u003c\/li\u003e\n\u003cli\u003eFinish: ready to paint after installation\u003c\/li\u003e\n\u003cli\u003eWeight: about 1.65 kg per length\u003c\/li\u003e\n\u003cli\u003eSold as: single length\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\u003cp\u003eExternal (outside) corners where two walls of \u003ca href=\"\/products\/james-hardie-finetex-cladding\"\u003eHardie Fine Texture cladding\u003c\/a\u003e (FineTex) or Hardie Brushed Concrete cladding meet. It holds the two panels tight and leaves a fine corner line. For a wider corner trim with 10 mm of coverage, see the \u003ca href=\"\/products\/james-hardie-external-corner-3-0m\"\u003eHardie 9mm aluminium external square corner\u003c\/a\u003e.\u003c\/p\u003e\u003ch2\u003eInstallation\u003c\/h2\u003e\u003cp\u003eFollow the Hardie Fine Texture Cladding and Hardie Brushed Concrete Cladding installation guide, listed under this product's documents. James Hardie says to cut the panel edges at 45 to 60 degrees where they meet the slimline corner. The corner goes on before the panels. It runs 60 mm below the bottom plate, and its bottom edge stays at least 90 mm clear of the ground. Run a continuous bead of sealant down the corner, then slide the panels in. Paint the corner with the wall. James Hardie asks for an exterior acrylic paint within 3 months of fixing, or within 7 days when the wall is within 1 km of the coast.\u003c\/p\u003e\u003ch2\u003eCommon questions\u003c\/h2\u003e\u003ch3\u003eWhich cladding does this corner suit?\u003c\/h3\u003e\u003cp\u003ePanels 8.5 mm thick. James Hardie lists Hardie Fine Texture Cladding and Hardie Brushed Concrete Cladding.\u003c\/p\u003e\u003ch3\u003eHow is it different from the square corner?\u003c\/h3\u003e\u003cp\u003eThe slimline corner covers 3.5 mm of the panel edge and needs the panel edges cut on an angle. The square corner covers 10 mm and takes square-cut panels.\u003c\/p\u003e\u003ch3\u003eHow many lengths do I need?\u003c\/h3\u003e\u003cp\u003eEach length is 3000 mm. Add up the height of every external corner, divide by 3.0 and round up. Allow extra for offcuts.\u003c\/p\u003e\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\u003cp\u003eYes. Pick up from our yard at 10 Lancaster Street, Ingleburn, or have it delivered across Sydney with the rest of your order. Call (02) 4605 0215 to check stock.\u003c\/p\u003e","brand":"Alpha Timber","offers":[{"title":"Default Title","offer_id":47748425679159,"sku":"306102","price":56.31,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/FineTex-9mm-Alu-Ext-Slimline-Corner-3.0m.png?v=1766108191"},{"product_id":"james-hardie-scyon-linea-16mm-aluminium-internal-corner-mould-3-6m","title":"James Hardie Linea 16mm aluminium internal corner mould 3600mm","description":"\u003cp\u003eThis is the James Hardie Linea 16 mm aluminium internal corner mould, a 3600 mm long aluminium extrusion that forms the internal corners on Linea Weatherboard walls. It is supplied ready to paint and gives a straight, clean line where two clad walls meet.\u003c\/p\u003e\u003ch2\u003eKey facts\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLength: 3600 mm\u003c\/li\u003e\n\u003cli\u003eMaterial: aluminium extrusion, internal corner profile\u003c\/li\u003e\n\u003cli\u003eFinish: ready to paint after installation\u003c\/li\u003e\n\u003cli\u003eMade for: James Hardie Linea Weatherboard (16 mm), internal corners\u003c\/li\u003e\n\u003cli\u003eWeight: about 1.4 kg per length\u003c\/li\u003e\n\u003cli\u003eJames Hardie product code: 305511\u003c\/li\u003e\n\u003cli\u003eSold as: single 3600 mm length\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\u003cp\u003eIt finishes the inside corners of a wall clad in Linea Weatherboard. The boards stop at the corner mould, so the corner reads as one straight line from top to bottom. James Hardie's product page lists it for Linea Weatherboard and for Stria Cladding. For Stria walls, see also the \u003ca href=\"\/products\/james-hardie-aluminium-internal-corner-3m\"\u003e14 mm aluminium internal corner\u003c\/a\u003e. For the outside corners of a Linea wall, see the \u003ca href=\"\/products\/james-hardie-scyon-linea-aluminium-external-slimline-boxed-corner-3-6m\"\u003eLinea external slimline boxed corner\u003c\/a\u003e.\u003c\/p\u003e\u003ch2\u003eInstallation\u003c\/h2\u003e\u003cp\u003eJames Hardie's Linea Weatherboard installation guide sets out the corner detail. In short: frame the corner with double studs, fit the corner mould with 40 mm nails at 400 mm vertical centres in both flanges, then install the boards leaving a nominal 2 mm gap to the aluminium corner. Where two lengths join, and at floor level, overlap by 50 mm with the upper section over the lower one. Follow the current guide for the full detail, and paint the corner with the wall.\u003c\/p\u003e\u003ch2\u003eCommon questions\u003c\/h2\u003e\u003ch3\u003eWhich cladding does this corner suit?\u003c\/h3\u003e\u003cp\u003eIt is made for 16 mm Linea Weatherboard. James Hardie also lists it for Stria Cladding. If you are using Axon or another Hardie cladding, ask us for the corner made for that product.\u003c\/p\u003e\u003ch3\u003eHow many do I need?\u003c\/h3\u003e\u003cp\u003eAdd up the height of every internal corner and divide by 3600 mm. Round up to whole lengths, and allow for the 50 mm overlap wherever two lengths join.\u003c\/p\u003e\u003ch3\u003eDoes it come painted?\u003c\/h3\u003e\u003cp\u003eNo. It is supplied ready to paint and is painted on site after installation.\u003c\/p\u003e\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\u003cp\u003eYes. Pick up from our yard at 10 Lancaster Street, Ingleburn, or have it delivered across Sydney. Call (02) 4605 0215 for a delivery quote. At 3.6 m long it needs racks, a long tray or a trailer.\u003c\/p\u003e","brand":"Alpha Timber","offers":[{"title":"Default Title","offer_id":47748425449783,"sku":"305511","price":109.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/Scyon-Linea-James-Hardie-16mm-Aluminium-Internal-Corner_Mould_3.6m.png?v=1766110778"},{"product_id":"james-hardie-scyon-linea-aluminium-external-slimline-boxed-corner-3-6m","title":"James Hardie Linea aluminium external slimline boxed corner 3600mm","description":"\u003cp\u003eThis is the James Hardie Linea aluminium external slimline boxed corner, a 3600 mm long aluminium extrusion that forms the external corners on Linea Weatherboard walls. It is supplied ready to paint and gives a straight, boxed corner where the weatherboards end.\u003c\/p\u003e\u003ch2\u003eKey facts\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLength: 3600 mm\u003c\/li\u003e\n\u003cli\u003eMaterial: aluminium extrusion, slimline boxed profile\u003c\/li\u003e\n\u003cli\u003eFinish: ready to paint after installation\u003c\/li\u003e\n\u003cli\u003eMade for: James Hardie Linea Weatherboard, external corners\u003c\/li\u003e\n\u003cli\u003eWeight: about 2 kg per length\u003c\/li\u003e\n\u003cli\u003eJames Hardie product code: 305512\u003c\/li\u003e\n\u003cli\u003eSold as: single 3600 mm length\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\u003cp\u003eIt finishes the outside corners of a wall clad in Linea Weatherboard. The boards stop at the corner piece, so the corner reads as one straight line from top to bottom. James Hardie lists it for Linea Weatherboard only. Other Hardie claddings have their own corner accessories.\u003c\/p\u003e\u003ch2\u003eInstallation\u003c\/h2\u003e\u003cp\u003eJames Hardie's Linea Weatherboard installation guide sets out the corner detail. In short: run the weather barrier continuously around the corner, fix the boxed corner with 40 mm fibre cement nails in the indentation provided, at 400 mm vertical centres through both flanges, then install the boards leaving a nominal 2 mm gap to the aluminium corner. On a cavity fix, the battens go on before the corner. James Hardie also lists caps to seal the bottom of the corner. Follow the current guide for the full detail, and paint the corner with the wall.\u003c\/p\u003e\u003ch2\u003eCommon questions\u003c\/h2\u003e\u003ch3\u003eWhich cladding does this corner suit?\u003c\/h3\u003e\u003cp\u003eJames Hardie lists it for Linea Weatherboard. If you are using Stria, Axon or another Hardie cladding, ask us for the corner made for that product.\u003c\/p\u003e\u003ch3\u003eHow many do I need?\u003c\/h3\u003e\u003cp\u003eJames Hardie's rule is wall height multiplied by the number of external corners, divided by 3600 mm. Round up to whole lengths.\u003c\/p\u003e\u003ch3\u003eDoes it come painted?\u003c\/h3\u003e\u003cp\u003eNo. It is supplied ready to paint and is painted on site after installation.\u003c\/p\u003e\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\u003cp\u003eYes. Pick up from our yard at 10 Lancaster Street, Ingleburn, or have it delivered across Sydney. Call (02) 4605 0215 for a delivery quote. At 3.6 m long it needs racks, a long tray or a trailer.\u003c\/p\u003e","brand":"Alpha Timber","offers":[{"title":"Default Title","offer_id":47748424007991,"sku":"305512","price":164.95,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/Scyon-Linea-Aluminium-External-Slimline-Boxed-Corner-3.6m.png?v=1766110946"},{"product_id":"james-hardie-linea-150mm-aluminium-corner-soaker","title":"Linea 150mm Alu Corner Soaker","description":"\u003cdiv\u003e\r\n\u003ch1\u003eLinea 150mm Alu Corner Soaker\u003c\/h1\u003e\r\n\u003cp\u003eLinea 150mm Alu Corner Soaker is a high-quality and durable product designed to provide excellent protection and reinforcement for corners in construction projects. Made from premium aluminum, this corner soaker is built to withstand harsh weather conditions and resist corrosion, ensuring long-lasting performance.\u003c\/p\u003e\r\n\r\n\u003ch2\u003eSpecifications:\u003c\/h2\u003e\r\n\u003cul\u003e\r\n\u003cli\u003eMaterial: Aluminum\u003c\/li\u003e\r\n\u003cli\u003eSize: 150mm\u003c\/li\u003e\r\n\u003cli\u003eUsage: Corner reinforcement in construction\u003c\/li\u003e\r\n\u003cli\u003eWeather-resistant and corrosion-resistant\u003c\/li\u003e\r\n\u003cli\u003eEasy to install and maintain\u003c\/li\u003e\r\n\u003c\/ul\u003e\r\n\r\n\u003cp\u003eUpgrade your construction projects with the Linea 150mm Alu Corner Soaker. Its superior quality and durability make it the perfect choice for reinforcing corners and ensuring long-term structural integrity. Don't miss out on this essential construction product!\u003c\/p\u003e\r\n\r\n\u003cp\u003e\u003cstrong\u003eShop now at Alpha Timber!\u003c\/strong\u003e\u003c\/p\u003e\r\n\u003c\/div\u003e","brand":"Alpha Timber","offers":[{"title":"Default Title","offer_id":47748423385399,"sku":"305574","price":7.99,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/Linea-150mm-Alu-Corner-Soaker.png?v=1766109768"},{"product_id":"james-hardie-h-jointer","title":"James Hardie 9mm aluminium horizontal h flashing jointer","description":"\u003cp\u003eThis is the James Hardie 9 mm aluminium horizontal h jointer, a ready to paint aluminium piece that joins two lengths of Hardie 9mm Aluminium Horizontal h Flashing end to end. It covers the join where one length of flashing stops and the next one starts.\u003c\/p\u003e\u003ch2\u003eKey facts\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eType: jointer for Hardie 9mm Aluminium Horizontal h Flashing\u003c\/li\u003e\n\u003cli\u003eMaterial: aluminium\u003c\/li\u003e\n\u003cli\u003eFinish: ready to paint after installation\u003c\/li\u003e\n\u003cli\u003eUsed on: Axon Cladding and EasyLap Panel walls (both James Hardie installation guides list it)\u003c\/li\u003e\n\u003cli\u003eJames Hardie product code: 305614\u003c\/li\u003e\n\u003cli\u003ePack: James Hardie supplies them in packs of 10. Call us to confirm whether you are buying one jointer or a pack\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\u003cp\u003eOn \u003ca href=\"\/products\/james-hardie-axon-cladding\"\u003eAxon Cladding\u003c\/a\u003e and \u003ca href=\"\/products\/james-hardie-easylap-cladding\"\u003eEasyLap Panel\u003c\/a\u003e walls, James Hardie's h flashing is an aluminium extrusion used along horizontal control joints, for example at floor level on a two storey wall. The flashing comes in 3000 mm lengths. Where two lengths meet, this jointer goes over the join. It joins flashing to flashing. It does not join the cladding panels themselves.\u003c\/p\u003e\u003ch2\u003eInstallation\u003c\/h2\u003e\u003cp\u003eThese points come from James Hardie's Axon Cladding installation guide (September 2026) and EasyLap Panel installation guide (October 2026), attached to this page.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eJoin the h flashings on an intermediate stud, not off the stud and not behind a sheet join.\u003c\/li\u003e\n\u003cli\u003eLeave a 2 mm gap between the two flashings behind the jointer.\u003c\/li\u003e\n\u003cli\u003eApply a continuous bead of Hardie Joint Sealant vertically between the h flashing and the jointer, 10 mm in from the ends.\u003c\/li\u003e\n\u003cli\u003eAdhere the jointer over the join.\u003c\/li\u003e\n\u003cli\u003ePaint it with the wall after installation.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eFollow the current guide for the full horizontal joint detail, including how the flashing is fixed and how the weather barrier laps over it.\u003c\/p\u003e\u003ch2\u003eCommon questions\u003c\/h2\u003e\u003ch3\u003eWhat does this jointer join?\u003c\/h3\u003e\u003cp\u003eTwo lengths of Hardie 9mm Aluminium Horizontal h Flashing, end to end. It is not a jointer for the panels.\u003c\/p\u003e\u003ch3\u003eHow many do I need?\u003c\/h3\u003e\u003cp\u003eOne for each place where two lengths of h flashing meet. James Hardie works out the flashing as the length of the horizontal joints divided by 3000 mm, so a straight run needs one jointer fewer than it has flashing lengths.\u003c\/p\u003e\u003ch3\u003eIs it sold singly or by the pack?\u003c\/h3\u003e\u003cp\u003eJames Hardie supplies these jointers in packs of 10. Call us on (02) 4605 0215 before ordering to confirm whether the listing is for one jointer or a pack.\u003c\/p\u003e\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\u003cp\u003eYes. Pick up from our yard at 10 Lancaster Street, Ingleburn, or have it delivered across Sydney with the rest of your cladding order.\u003c\/p\u003e","brand":"Alpha Timber","offers":[{"title":"Default Title","offer_id":47197294068023,"sku":"305614","price":2.43,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/JH_h_Jointer.png?v=1766109117"},{"product_id":"james-hardie-linea-cladding","title":"James Hardie Linea Weatherboard 16mm, 4200 x 150mm fibre cement","description":"\u003cp\u003eLinea Weatherboard is James Hardie's 16 mm thick fibre cement weatherboard, sold here as a 4200 x 150 mm board. The pre-primed boards are lapped and fixed across timber or light steel wall frames as external cladding with deep shadow lines, then painted. It was sold before as Scyon Linea.\u003c\/p\u003e\u003ch2\u003eKey facts\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eThickness: 16 mm\u003c\/li\u003e\n\u003cli\u003eBoard size: 4200 x 150 mm (4205 mm overall with the tongue and groove end)\u003c\/li\u003e\n\u003cli\u003eMaterial: fibre cement, pre-primed\u003c\/li\u003e\n\u003cli\u003eEnds: tongue and groove short ends, so boards can join off the stud\u003c\/li\u003e\n\u003cli\u003eWeight: about 2.8 kg per metre, so about 12 kg per board (James Hardie's guide)\u003c\/li\u003e\n\u003cli\u003eCover: at the 30 mm lap, 120 mm per row, about 0.50 m² per board\u003c\/li\u003e\n\u003cli\u003eJames Hardie product code: 403930\u003c\/li\u003e\n\u003cli\u003eSold as: single boards\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\u003cp\u003eExternal wall cladding with a classic narrow weatherboard look. James Hardie's guide covers residential walls over a seasoned timber frame or a light gauge steel frame. For the wider board, see \u003ca href=\"\/products\/scyon-linea-4200x180x16mm\"\u003eLinea Weatherboard 180 mm\u003c\/a\u003e. For corners, see the \u003ca href=\"\/products\/james-hardie-scyon-linea-aluminium-external-slimline-boxed-corner-3-6m\"\u003eLinea external slimline boxed corner\u003c\/a\u003e and the \u003ca href=\"\/products\/james-hardie-scyon-linea-16mm-aluminium-internal-corner-mould-3-6m\"\u003eLinea internal corner mould\u003c\/a\u003e.\u003c\/p\u003e\u003ch2\u003eInstallation\u003c\/h2\u003e\u003cp\u003eThese points come from James Hardie's Linea Weatherboard installation guide (September 2026), attached to this page.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eStud spacing depends on the wind class. It is 600 mm maximum up to N3\/C1, and closer near building edges and in higher wind classes. Check Table 3 of the guide for your site.\u003c\/li\u003e\n\u003cli\u003eLap each board 30 mm over the one below.\u003c\/li\u003e\n\u003cli\u003eTimber frames: face nail with 60 x 3.15 mm bullet head nails, or conceal nail with 40 x 2.8 mm fibre cement nails or Paslode 45 x 2.5 mm ring shank coil nails. Steel frames: 41 mm Hardie Drive screws.\u003c\/li\u003e\n\u003cli\u003eWithin 1 km of the coast, James Hardie calls for class 4 fasteners.\u003c\/li\u003e\n\u003cli\u003eEnd joints are tongue and groove and sit off the stud, at least 100 mm from the side of a stud. Run a continuous bead of Hardie Joint Sealant on the back of the tongue and push the boards firmly together. Keep joints in adjacent rows at least one stud spacing apart.\u003c\/li\u003e\n\u003cli\u003eKeep at least 150 mm clearance to the ground and 50 mm to roofs, decks, paths, steps and driveways.\u003c\/li\u003e\n\u003cli\u003ePaint within 3 months of fixing, or within 7 days if the site is within 1 km of the coast. James Hardie recommends at least two coats of quality exterior acrylic paint.\u003c\/li\u003e\n\u003cli\u003eFibre cement dust contains silica. Cut outdoors with a hand guillotine, fibreshear or a dust-reducing saw with an M class vacuum. Wear a P2 respirator, and never use a grinder or dry sweep the dust.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eFollow the current James Hardie guide for the full detail. For bracing, fire rated walls or anything structural, check with your building designer or engineer.\u003c\/p\u003e\u003ch2\u003eCommon questions\u003c\/h2\u003e\u003ch3\u003eHow many boards do I need?\u003c\/h3\u003e\u003cp\u003eAt the 30 mm lap each row covers 120 mm, so you need about 8.3 rows for every metre of wall height. One 4200 mm board covers about 0.50 m². Divide your wall area by that figure and add an allowance for offcuts around windows and doors.\u003c\/p\u003e\u003ch3\u003eDo the end joints have to land on a stud?\u003c\/h3\u003e\u003cp\u003eNo. The short ends are tongue and groove and are joined off the stud, at least 100 mm from the side of a stud, with sealant on the back of the tongue.\u003c\/p\u003e\u003ch3\u003eDoes Linea need painting?\u003c\/h3\u003e\u003cp\u003eYes. The boards are pre-primed and must be painted within 3 months of being installed, or within 7 days near the coast.\u003c\/p\u003e\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\u003cp\u003eYes. Pick up from our yard at 10 Lancaster Street, Ingleburn, or ask us about delivery across Sydney. Call (02) 4605 0215 to check stock. The boards are 4.2 m long, so bring racks, a long tray or a trailer.\u003c\/p\u003e","brand":"Alpha Timber","offers":[{"title":"Default Title","offer_id":47197296492855,"sku":"403930","price":44.55,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/Linea-4200x150x16mm.png?v=1766109875"},{"product_id":"james-hardie-easylap-cladding","title":"James Hardie EasyLap panel 8.5mm fibre cement cladding","description":"\u003cp\u003eJames Hardie EasyLap panel is an 8.5 mm pre-primed fibre cement cladding sheet with a shiplap joint along its two long edges. It is fixed vertically to timber or steel framed walls and finished on site with a roll-on textured acrylic paint for a rendered look.\u003c\/p\u003e\n\u003ch2\u003eKey facts\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eThickness: 8.5 mm\u003c\/li\u003e\n\u003cli\u003eSizes: 2440 x 1200 mm, 3000 x 900 mm, 3000 x 1200 mm and 3600 x 1200 mm\u003c\/li\u003e\n\u003cli\u003eMaterial: fibre cement, pre-primed\u003c\/li\u003e\n\u003cli\u003eEdges: shiplap joint on the two long edges\u003c\/li\u003e\n\u003cli\u003eWeight (James Hardie, approximate): 38 kg (2440 x 1200), 35 kg (3000 x 900), 47 kg (3000 x 1200), 56 kg (3600 x 1200). About 13 kg per m²\u003c\/li\u003e\n\u003cli\u003eCoverage per sheet: 2.93 m², 2.7 m², 3.6 m² and 4.32 m²\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\n\u003cp\u003eExternal wall cladding on houses and medium-density residential buildings, including alterations and additions. James Hardie's guide covers fixing direct to the frame or over cavity battens, on timber or light gauge steel framing.\u003c\/p\u003e\n\u003ch2\u003eInstallation\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003ePanels run vertically. Stud or batten spacing depends on the wind class of the site: 600 mm maximum for N1 to N4, closer for higher wind classes.\u003c\/li\u003e\n\u003cli\u003eRun a bead of joint sealant along the shiplap edge and use sealing tape behind vertical joints, as shown in the guide.\u003c\/li\u003e\n\u003cli\u003eKeep at least 150 mm clearance between the bottom of the cladding and the ground.\u003c\/li\u003e\n\u003cli\u003ePaint within 3 months of fixing, or within 7 days if the site is within 1 km of the coast.\u003c\/li\u003e\n\u003cli\u003eFibre cement dust contains silica. Cut outdoors with a dust-reducing saw and vacuum extraction, wear a P2 respirator, and never use a grinder or dry sweep the dust.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eFollow the current James Hardie EasyLap Panel installation guide for framing, fixings and weatherproofing. For anything structural or fire rated, check with your building designer or engineer.\u003c\/p\u003e\n\u003ch2\u003eCommon questions\u003c\/h2\u003e\n\u003ch3\u003eHow heavy is a sheet of EasyLap?\u003c\/h3\u003e\n\u003cp\u003eJames Hardie lists about 38 kg for a 2440 x 1200 sheet, 47 kg for 3000 x 1200 and 56 kg for 3600 x 1200. Plan on two people to carry and fix the larger sheets.\u003c\/p\u003e\n\u003ch3\u003eDoes EasyLap need painting?\u003c\/h3\u003e\n\u003cp\u003eYes. The panel comes pre-primed and is finished on site with a roll-on textured acrylic paint. James Hardie says to paint within 3 months of fixing, or within 7 days near the coast.\u003c\/p\u003e\n\u003ch3\u003eHow many sheets do I need?\u003c\/h3\u003e\n\u003cp\u003eDivide the wall area by the sheet coverage: 2.93 m² for 2440 x 1200, 3.6 m² for 3000 x 1200 and 4.32 m² for 3600 x 1200. Allow extra for offcuts around windows and doors.\u003c\/p\u003e\n\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\n\u003cp\u003eYes. Pick up from our yard at 10 Lancaster Street, Ingleburn, or ask us about delivery across Sydney. Call (02) 4605 0215 to check stock on the size you need.\u003c\/p\u003e","brand":"James Hardie","offers":[{"title":"2440x1200x8.5mm","offer_id":47896279810359,"sku":"404184","price":122.98,"currency_code":"AUD","in_stock":true},{"title":"3000x900x8.5mm","offer_id":47896534057271,"sku":"404186","price":121.04,"currency_code":"AUD","in_stock":false},{"title":"3000x1200x8.5mm","offer_id":47896534090039,"sku":"404185","price":151.21,"currency_code":"AUD","in_stock":true},{"title":"3600x1200x8.5mm","offer_id":47896534122807,"sku":"404980","price":191.03,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/James-Hardie-Easylap-Cladding.png?v=1766107704"},{"product_id":"james-hardie-external-corner-3-0m","title":"James Hardie 9mm aluminium external square corner 3000mm","description":"\u003cp\u003eThe Hardie 9mm aluminium external square corner is a 3000 mm aluminium trim that finishes the outside corners of James Hardie panel cladding. It suits cladding panels 8.5 to 9 mm thick and gives 10 mm of coverage over the panel edges.\u003c\/p\u003e\n\u003ch2\u003eKey facts\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eBrand: James Hardie, product code 306100\u003c\/li\u003e\n\u003cli\u003eLength: 3000 mm (3.0 m)\u003c\/li\u003e\n\u003cli\u003eMaterial: aluminium\u003c\/li\u003e\n\u003cli\u003eSuits cladding panels 8.5 to 9 mm thick\u003c\/li\u003e\n\u003cli\u003eCoverage: 10 mm\u003c\/li\u003e\n\u003cli\u003eFinish: ready to paint after installation\u003c\/li\u003e\n\u003cli\u003eWeight: about 1.8 kg per length\u003c\/li\u003e\n\u003cli\u003eSold as: single length\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\n\u003cp\u003eExternal (outside) corners where two walls of 9 mm fibre cement panel cladding meet. James Hardie lists it as compatible with Axon cladding, Hardie Fine Texture cladding and Hardie Brushed Concrete cladding. It covers the cut panel edges and gives a straight, square corner line.\u003c\/p\u003e\n\u003ch2\u003eInstallation\u003c\/h2\u003e\n\u003cp\u003eFit the corner as shown in the James Hardie installation guide for the cladding you are using. The guide sets out the fixing, sealing and clearances for that system. Cut the aluminium with a hacksaw or a fine-tooth metal blade and remove any burrs. Paint it after installation, along with the cladding. For 14 mm cladding, use the \u003ca href=\"\/products\/hardie-14mm-alum-external-corner-3000mm\"\u003eHardie 14mm aluminium external corner\u003c\/a\u003e instead.\u003c\/p\u003e\n\u003ch2\u003eCommon questions\u003c\/h2\u003e\n\u003ch3\u003eWhich cladding does this corner suit?\u003c\/h3\u003e\n\u003cp\u003ePanels 8.5 to 9 mm thick. James Hardie lists Axon, Hardie Fine Texture and Hardie Brushed Concrete cladding.\u003c\/p\u003e\n\u003ch3\u003eHow many lengths do I need?\u003c\/h3\u003e\n\u003cp\u003eEach length is 3000 mm. A wall up to 3.0 m high needs one length per external corner. Allow extra for taller walls and offcuts.\u003c\/p\u003e\n\u003ch3\u003eDoes it come painted?\u003c\/h3\u003e\n\u003cp\u003eNo colour finish is stated by James Hardie. It is described as ready to paint after installation, so paint it with the cladding.\u003c\/p\u003e\n\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\n\u003cp\u003eYes. Pick up from our yard at 10 Lancaster Street, Ingleburn, or have it delivered across Sydney with the rest of your order. Call (02) 4605 0215 to check stock.\u003c\/p\u003e","brand":"Alpha Timber","offers":[{"title":"Default Title","offer_id":47748419977527,"sku":"306100","price":89.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/JH-9mm-Aluminium-External-Square-Corner.png?v=1766107886"},{"product_id":"james-hardie-aluminium-internal-corner-3m","title":"James Hardie 14mm aluminium internal corner 3000mm","description":"\u003cp\u003eThis is the James Hardie 14mm aluminium internal corner, a 3000 mm long aluminium extrusion that forms the internal corners on walls clad in Stria Cladding. It is supplied ready to paint.\u003c\/p\u003e\u003ch2\u003eKey facts\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLength: 3000 mm\u003c\/li\u003e\n\u003cli\u003eSize: 14 mm\u003c\/li\u003e\n\u003cli\u003eMaterial: aluminium extrusion\u003c\/li\u003e\n\u003cli\u003eFinish: ready to paint\u003c\/li\u003e\n\u003cli\u003eMade for: James Hardie Stria Cladding, internal corners\u003c\/li\u003e\n\u003cli\u003eWeight: about 1.35 kg per length\u003c\/li\u003e\n\u003cli\u003eJames Hardie product code: 305518\u003c\/li\u003e\n\u003cli\u003eSold as: single 3000 mm length\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\u003cp\u003eIt goes into the inside corner where two Stria-clad walls meet, so the boards finish against a straight aluminium line. Internal corner here means an inside corner of a clad wall. It is not a trim for plasterboard or other interior linings. James Hardie lists it for Stria Cladding.\u003c\/p\u003e\u003ch2\u003eInstallation\u003c\/h2\u003e\u003cp\u003eJames Hardie's Stria Cladding installation guides, horizontal and vertical, show the internal corner detail. In short: fix the aluminium corner with 40 mm fibre cement nails at 300 mm vertical centres through both flanges, then install the boards leaving a nominal 2 mm gap to the aluminium corner. The guides also call for a continuous bead of Hardie Joint Sealant at the corner flashing. Follow the current guide for the full detail and the order of work, and paint the corner with the wall.\u003c\/p\u003e\u003ch2\u003eCommon questions\u003c\/h2\u003e\u003ch3\u003eWhich cladding does this corner suit?\u003c\/h3\u003e\u003cp\u003eJames Hardie lists it for Stria Cladding. James Hardie also makes a 9mm aluminium internal corner, so ask us which one your cladding needs.\u003c\/p\u003e\u003ch3\u003eHow many do I need?\u003c\/h3\u003e\u003cp\u003eMultiply the wall height by the number of internal corners and divide by 3000 mm. Round up to whole lengths.\u003c\/p\u003e\u003ch3\u003eDoes it come painted?\u003c\/h3\u003e\u003cp\u003eNo. It is supplied ready to paint and is painted on site.\u003c\/p\u003e\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\u003cp\u003eYes. Pick up from our yard at 10 Lancaster Street, Ingleburn, or have it delivered across Sydney. Call (02) 4605 0215 for a delivery quote. At 3.0 m long it needs racks, a tray or a trailer.\u003c\/p\u003e","brand":"Alpha Timber","offers":[{"title":"Default Title","offer_id":47748419715383,"sku":"305518","price":76.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/JH-Alu-Int-Corner-3m.png?v=1766105868"},{"product_id":"james-hardie-scyon-axent-trim","title":"James Hardie Axent Trim 3000mm fibre cement trim, 45x19 to 89x38","description":"\u003cp\u003eHardie Axent Trim is a fibre cement trim from James Hardie, sold in 3000 mm lengths in 45 x 19, 45 x 38 and 89 x 38 mm. It is used for box corners and as decorative trim around windows and doors on fibre cement cladding.\u003c\/p\u003e\u003ch2\u003eKey facts\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eBrand: James Hardie. Also known by its older name, Scyon Axent Trim\u003c\/li\u003e\n\u003cli\u003eSizes: 45 x 19 mm (code 405260), 45 x 38 mm (code 405261) and 89 x 38 mm (code 405262)\u003c\/li\u003e\n\u003cli\u003eLength: 3000 mm (3.0 m)\u003c\/li\u003e\n\u003cli\u003eMaterial: fibre cement\u003c\/li\u003e\n\u003cli\u003eFinish: pre-sealed, with chamfered front faces. Paint after installation\u003c\/li\u003e\n\u003cli\u003eWeight per length: about 3 kg (45 x 19), 6 kg (45 x 38) and 12 kg (89 x 38)\u003c\/li\u003e\n\u003cli\u003eSold as: single lengths\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\u003cp\u003eJames Hardie's guide lists box corners, trim around windows and doors, finishing internal and external corners, covering butt joints and battens for a board and batten look. The guide shows it with cladding such as \u003ca href=\"\/products\/james-hardie-finetex-cladding\"\u003eHardie Fine Texture cladding\u003c\/a\u003e, Hardie Brushed Concrete cladding and Linea Weatherboard. The cladding can butt up to the trim, or the trim can sit over the cladding.\u003c\/p\u003e\u003ch2\u003eInstallation\u003c\/h2\u003e\u003cp\u003eFollow James Hardie's Axent Trim installation guide (March 2024), listed under this product's documents. In short:\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFix the trim directly to timber framing, with two fasteners at each end.\u003c\/li\u003e\n\u003cli\u003e19 mm trim: 50 mm 16 gauge brads at 150 mm centres, or 2.8 x 50 mm nails in pre-drilled holes at 300 mm centres.\u003c\/li\u003e\n\u003cli\u003e38 mm trim: 62 mm 16 gauge brads at 150 mm centres, or 2.8 x 65 mm nails in pre-drilled holes at 300 mm centres.\u003c\/li\u003e\n\u003cli\u003eGas nail guns are not suitable. James Hardie recommends stainless steel finishing nails.\u003c\/li\u003e\n\u003cli\u003ePrime edges cut on site before you fix the trim. Leave a gap of up to 2 mm at joints and seal with Hardie Joint Sealant.\u003c\/li\u003e\n\u003cli\u003eKeep the trim 150 mm clear of the ground and 50 mm clear of roofs, decks and paths.\u003c\/li\u003e\n\u003cli\u003ePaint within 3 months with at least two coats of quality acrylic paint. The trim must be dry before painting.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eFibre cement contains sand, a source of crystalline silica. Cut it outdoors with a dust-reducing method and wear a P1 or better respirator. The guide also covers steel framing and screw fixing.\u003c\/p\u003e\u003ch2\u003eCommon questions\u003c\/h2\u003e\u003ch3\u003eWhat sizes does Axent Trim come in here?\u003c\/h3\u003e\u003cp\u003eThree sizes, all 3000 mm long: 45 x 19 mm, 45 x 38 mm and 89 x 38 mm. Choose the size above.\u003c\/p\u003e\u003ch3\u003eHow heavy is a length?\u003c\/h3\u003e\u003cp\u003eAbout 3 kg for 45 x 19, 6 kg for 45 x 38 and 12 kg for 89 x 38, from James Hardie's guide.\u003c\/p\u003e\u003ch3\u003eDoes it need painting?\u003c\/h3\u003e\u003cp\u003eYes. It comes pre-sealed, not finished. James Hardie asks for at least two coats of quality acrylic paint within 3 months of installing it.\u003c\/p\u003e\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\u003cp\u003eYes. Pick up from our yard at 10 Lancaster Street, Ingleburn, or have it delivered across Sydney with the rest of your order. Call (02) 4605 0215 to check stock.\u003c\/p\u003e","brand":"Alpha Timber","offers":[{"title":"45x19x3000mm","offer_id":47896278270263,"sku":"405260","price":37.5,"currency_code":"AUD","in_stock":true},{"title":"45x38x3000mm","offer_id":47896533205303,"sku":"405261","price":64.99,"currency_code":"AUD","in_stock":false},{"title":"89x38x3000mm","offer_id":47896533238071,"sku":"405262","price":86.0,"currency_code":"AUD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/James-Hardie-Scyon-Axent-Trim.jpg?v=1766110642"},{"product_id":"james-hardie-75mm-colorbond-corner-flashing-3-0m","title":"James HardieTM 75x75mm Colorbond Corner Flashing 3.0m","description":"\u003cdiv\u003e\n\u003ch1\u003eJames HardieTM 75x75mm Colorbond Corner Flashing 3.0m\u003c\/h1\u003e\n\u003cp\u003eEnhance the durability and aesthetics of your building corners with James HardieTM 75x75mm Colorbond Corner Flashing. This high-quality flashing is designed to protect and seal the vulnerable corners of your structure, ensuring long-lasting performance and a sleek finish.\u003c\/p\u003e\n\u003ch2\u003eSpecifications:\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eDimensions: 75x75mm\u003c\/li\u003e\n\u003cli\u003eMaterial: Colorbond\u003c\/li\u003e\n\u003cli\u003eLength: 3.0m\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eAdvantages:\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eProvides excellent protection and sealing for building corners\u003c\/li\u003e\n\u003cli\u003eDurable Colorbond material ensures long-lasting performance\u003c\/li\u003e\n\u003cli\u003eEnhances the aesthetics of your structure with a sleek finish\u003c\/li\u003e\n\u003cli\u003eEasy to install and maintain\u003c\/li\u003e\n\u003cli\u003eResistant to corrosion, weather, and UV rays\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ca href=\"https:\/\/alphatimber.com.au\/\"\u003eShop now at Alpha Timber!\u003c\/a\u003e\n\u003c\/div\u003e","brand":"Alpha Timber","offers":[{"title":"Default Title","offer_id":47748373348663,"sku":"305564","price":59.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/James_HardieTM_75x75mm-Colorbond-Corner-Flashing-3.0m.png?v=1766105017"},{"product_id":"hardie-14mm-alum-external-corner-3000mm","title":"James Hardie 14mm aluminium external corner 3000mm","description":"\u003cp\u003eThe Hardie 14mm aluminium external corner is a 3000 mm ready to paint aluminium extrusion from James Hardie. It is used to form boxed external corners on James Hardie cladding.\u003c\/p\u003e\n\u003ch2\u003eKey facts\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eBrand: James Hardie, product code 305519\u003c\/li\u003e\n\u003cli\u003eLength: 3000 mm (3.0 m)\u003c\/li\u003e\n\u003cli\u003eMaterial: aluminium extrusion\u003c\/li\u003e\n\u003cli\u003eProfile: 14 mm external boxed corner\u003c\/li\u003e\n\u003cli\u003eFinish: ready to paint\u003c\/li\u003e\n\u003cli\u003eWeight: about 1.5 kg per length\u003c\/li\u003e\n\u003cli\u003eSold as: single length\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\n\u003cp\u003eExternal (outside) corners where two clad walls meet. The extrusion covers the cut cladding edges and gives a straight boxed corner. James Hardie describes it as corrosion resistant and robust against impact.\u003c\/p\u003e\n\u003ch2\u003eInstallation\u003c\/h2\u003e\n\u003cp\u003eFit the corner as shown in the James Hardie installation guide for the cladding you are using. The guide sets out the fixing, sealing and clearances for that system. Cut the aluminium with a hacksaw or a fine-tooth metal blade and remove any burrs. Paint it after installation, along with the cladding.\u003c\/p\u003e\n\u003ch2\u003eCommon questions\u003c\/h2\u003e\n\u003ch3\u003eWhich cladding does this corner suit?\u003c\/h3\u003e\n\u003cp\u003eJames Hardie's page for this corner does not list the cladding it matches. Check the accessories table in the installation guide for your cladding before you order, or call us with the cladding name and thickness. For panels 8.5 to 9 mm thick, use the \u003ca href=\"\/products\/james-hardie-external-corner-3-0m\"\u003eHardie 9mm aluminium external square corner\u003c\/a\u003e.\u003c\/p\u003e\n\u003ch3\u003eHow many lengths do I need?\u003c\/h3\u003e\n\u003cp\u003eEach length is 3000 mm. A wall up to 3.0 m high needs one length per external corner. Allow extra for taller walls and offcuts.\u003c\/p\u003e\n\u003ch3\u003eDoes it come painted?\u003c\/h3\u003e\n\u003cp\u003eNo. James Hardie supplies it ready to paint, so paint it with the cladding.\u003c\/p\u003e\n\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\n\u003cp\u003eYes. Pick up from our yard at 10 Lancaster Street, Ingleburn, or have it delivered across Sydney with the rest of your order. Call (02) 4605 0215 to check stock.\u003c\/p\u003e","brand":"Alpha Timber","offers":[{"title":"Default Title","offer_id":47707450835255,"sku":"305519","price":99.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/external-corner-aluminium.png?v=1754675980"},{"product_id":"scyon-linea-4200x180x16mm","title":"James Hardie Linea Weatherboard 16mm, 4200 x 180mm fibre cement","description":"\u003cp\u003eLinea Weatherboard is James Hardie's 16 mm thick fibre cement weatherboard, sold here as a 4200 x 180 mm board. The pre-primed boards are lapped and fixed across timber or light steel wall frames as external cladding with deep shadow lines, then painted. It was sold before as Scyon Linea.\u003c\/p\u003e\u003ch2\u003eKey facts\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eThickness: 16 mm\u003c\/li\u003e\n\u003cli\u003eBoard size: 4200 x 180 mm (4205 mm overall with the tongue and groove end)\u003c\/li\u003e\n\u003cli\u003eMaterial: fibre cement, pre-primed\u003c\/li\u003e\n\u003cli\u003eEnds: tongue and groove short ends, so boards can join off the stud\u003c\/li\u003e\n\u003cli\u003eWeight: about 3.4 kg per metre, so about 14 kg per board (James Hardie's guide)\u003c\/li\u003e\n\u003cli\u003eCover: at the 30 mm lap, 150 mm per row, about 0.63 m² per board\u003c\/li\u003e\n\u003cli\u003eJames Hardie product code: 403912\u003c\/li\u003e\n\u003cli\u003eSold as: single boards\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\u003cp\u003eExternal wall cladding with a wide weatherboard look. James Hardie's guide covers residential walls over a seasoned timber frame or a light gauge steel frame. For the narrower board, see \u003ca href=\"\/products\/james-hardie-linea-cladding\"\u003eLinea Weatherboard 150 mm\u003c\/a\u003e. For corners, see the \u003ca href=\"\/products\/james-hardie-scyon-linea-aluminium-external-slimline-boxed-corner-3-6m\"\u003eLinea external slimline boxed corner\u003c\/a\u003e and the \u003ca href=\"\/products\/james-hardie-scyon-linea-16mm-aluminium-internal-corner-mould-3-6m\"\u003eLinea internal corner mould\u003c\/a\u003e.\u003c\/p\u003e\u003ch2\u003eInstallation\u003c\/h2\u003e\u003cp\u003eThese points come from James Hardie's Linea Weatherboard installation guide (September 2026), attached to this page.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eStud spacing depends on the wind class. It is 600 mm maximum up to N3\/C1, and closer near building edges and in higher wind classes. Check Table 3 of the guide for your site.\u003c\/li\u003e\n\u003cli\u003eLap each board 30 mm over the one below.\u003c\/li\u003e\n\u003cli\u003eTimber frames: face nail with 60 x 3.15 mm bullet head nails, or conceal nail with 40 x 2.8 mm fibre cement nails or Paslode 45 x 2.5 mm ring shank coil nails. Steel frames: 41 mm Hardie Drive screws.\u003c\/li\u003e\n\u003cli\u003eWithin 1 km of the coast, James Hardie calls for class 4 fasteners.\u003c\/li\u003e\n\u003cli\u003eEnd joints are tongue and groove and sit off the stud, at least 100 mm from the side of a stud. Run a continuous bead of Hardie Joint Sealant on the back of the tongue and push the boards firmly together. Keep joints in adjacent rows at least one stud spacing apart.\u003c\/li\u003e\n\u003cli\u003eKeep at least 150 mm clearance to the ground and 50 mm to roofs, decks, paths, steps and driveways.\u003c\/li\u003e\n\u003cli\u003ePaint within 3 months of fixing, or within 7 days if the site is within 1 km of the coast. James Hardie recommends at least two coats of quality exterior acrylic paint.\u003c\/li\u003e\n\u003cli\u003eFibre cement dust contains silica. Cut outdoors with a hand guillotine, fibreshear or a dust-reducing saw with an M class vacuum. Wear a P2 respirator, and never use a grinder or dry sweep the dust.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eFollow the current James Hardie guide for the full detail. For bracing, fire rated walls or anything structural, check with your building designer or engineer.\u003c\/p\u003e\u003ch2\u003eCommon questions\u003c\/h2\u003e\u003ch3\u003eHow many boards do I need?\u003c\/h3\u003e\u003cp\u003eAt the 30 mm lap each row covers 150 mm, so you need about 6.7 rows for every metre of wall height. One 4200 mm board covers about 0.63 m². Divide your wall area by that figure and add an allowance for offcuts around windows and doors.\u003c\/p\u003e\u003ch3\u003eDo the end joints have to land on a stud?\u003c\/h3\u003e\u003cp\u003eNo. The short ends are tongue and groove and are joined off the stud, at least 100 mm from the side of a stud, with sealant on the back of the tongue.\u003c\/p\u003e\u003ch3\u003eDoes Linea need painting?\u003c\/h3\u003e\u003cp\u003eYes. The boards are pre-primed and must be painted within 3 months of being installed, or within 7 days near the coast.\u003c\/p\u003e\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\u003cp\u003eYes. Pick up from our yard at 10 Lancaster Street, Ingleburn, or ask us about delivery across Sydney. Call (02) 4605 0215 to check stock. The boards are 4.2 m long, so bring racks, a long tray or a trailer.\u003c\/p\u003e","brand":"Alpha Timber","offers":[{"title":"Default Title","offer_id":47796294353207,"sku":"403912","price":55.77,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/Scyon-Linea-4200x180x16mm.jpg?v=1766391907"},{"product_id":"stria-alu-ext-box-corner-3m","title":"James Hardie Stria 14mm aluminium external box corner 3000mm","description":"\u003cp\u003eThe James Hardie 14mm aluminium external box corner is a ready to paint aluminium extrusion, 3000 mm long. It forms a boxed outside corner where two walls of Stria Cladding meet. James Hardie product code 305519.\u003c\/p\u003e\u003ch2\u003eKey facts\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLength: 3000 mm\u003c\/li\u003e\n\u003cli\u003eFor: 14 mm James Hardie Stria Cladding\u003c\/li\u003e\n\u003cli\u003eMaterial: aluminium extrusion, ready to paint\u003c\/li\u003e\n\u003cli\u003eWeight: about 1.5 kg per length\u003c\/li\u003e\n\u003cli\u003eSold as: single length (James Hardie packs them in fives)\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\u003cp\u003eFinishing the external corners of walls clad in Stria Cladding. The boards stop at the corner piece on each wall, which gives a square, boxed corner. For inside corners, see the \u003ca href=\"\/products\/james-hardie-aluminium-internal-corner-3m\"\u003eJames Hardie 14mm aluminium internal corner\u003c\/a\u003e.\u003c\/p\u003e\u003ch2\u003eInstallation\u003c\/h2\u003e\u003cp\u003eJames Hardie's Stria Cladding installation guide shows the corner fixed with 40 mm fibre cement nails at 300 mm vertical centres in both flanges. The boards are then installed with a nominal 2 mm gap to the aluminium corner, and the gap is sealed with Hardie Joint Sealant. Paint the corner with the cladding. Follow the current James Hardie guide for the full corner detail, including the flashing behind it.\u003c\/p\u003e\u003ch2\u003eCommon questions\u003c\/h2\u003e\u003ch3\u003eHow many lengths do I need?\u003c\/h3\u003e\u003cp\u003eJames Hardie's rule is wall height times the number of external corners, divided by 3000 mm. For example, four corners on a 2.7 m high wall is 10.8 m, so order four lengths.\u003c\/p\u003e\u003ch3\u003eDoes it need painting?\u003c\/h3\u003e\u003cp\u003eYes. It is supplied ready to paint and is painted on site with the cladding.\u003c\/p\u003e\u003ch3\u003eDoes it suit other cladding?\u003c\/h3\u003e\u003cp\u003eJames Hardie lists it as the external box corner for Stria Cladding. For 8.5 to 9 mm panels such as Axon or Hardie Fine Texture, see the \u003ca href=\"\/products\/james-hardie-9mm-aluminum-external-square-corner\"\u003e9mm aluminium external square corner\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\u003cp\u003eYes. Pick up from our yard at 10 Lancaster Street, Ingleburn, or we can deliver across Sydney.\u003c\/p\u003e","brand":"Alpha Timber","offers":[{"title":"Default Title","offer_id":47796294484279,"sku":"305519","price":99.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/STRIA-14mm-Aluminum-External-Box-Corner.png?v=1754675969"},{"product_id":"james-hardie-joint-sealent-grey-300ml-cartridge-20-box","title":"James Hardie joint Sealent White 300ml Cartridge 20\/Box","description":"\u003cdiv\u003e\n\u003ch1\u003eJames Hardie Joint Sealant White 300ml Cartridge 20\/Box\u003c\/h1\u003e\n\u003cp\u003eJames Hardie Joint Sealant White is a high-quality sealant designed specifically for use with James Hardie products. It provides a strong and durable bond, ensuring a long-lasting and secure joint.\u003c\/p\u003e\n\u003ch2\u003eSpecifications:\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eColor:  White\u003c\/li\u003e\n\u003cli\u003eSize: 300ml Cartridge\u003c\/li\u003e\n\u003cli\u003eQuantity: 20 per box\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eAdvantages:\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eHigh-quality sealant for James Hardie products\u003c\/li\u003e\n\u003cli\u003eStrong and durable bond\u003c\/li\u003e\n\u003cli\u003eLong-lasting and secure joint\u003c\/li\u003e\n\u003cli\u003eEasy to apply and work with\u003c\/li\u003e\n\u003cli\u003eProvides excellent weather resistance\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eCall to Action:\u003c\/h2\u003e\n\u003cp\u003eGet your James Hardie Joint Sealant White now at Alpha Timber!\u003c\/p\u003e\n\u003c\/div\u003e","brand":"Alpha Timber","offers":[{"title":"Default Title","offer_id":47796299825463,"sku":"305534","price":25.99,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/James-Hardie-joint-Sealent-White-300ml-Cartridge-20_Box.png?v=1766109630"},{"product_id":"hardieedge-base-trim-jointer","title":"Hardie Edge base trim jointer, aluminium, by James Hardie","description":"\u003cp\u003eThe Hardie Edge Base Trim Jointer is a James Hardie aluminium jointer that conceals the join where two lengths of Hardie Edge Base Trim meet. Hardie Edge Trim is James Hardie's powder coated aluminium trim for the slab edge at the bottom of a clad wall.\u003c\/p\u003e\u003ch2\u003eKey facts\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eType: jointer for Hardie Edge Base Trim\u003c\/li\u003e\n\u003cli\u003eMaterial: powder coated aluminium extrusion\u003c\/li\u003e\n\u003cli\u003eColour: Sable Brilliance (dark grey), as stated by James Hardie\u003c\/li\u003e\n\u003cli\u003eJames Hardie product code: 305912\u003c\/li\u003e\n\u003cli\u003eUsed with: Hardie Edge Base Trim, which comes in 3950 mm lengths\u003c\/li\u003e\n\u003cli\u003ePack: James Hardie supplies them in packs of 12. Call us to confirm whether you are buying one jointer or a pack\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\u003cp\u003eHardie Edge Trim finishes the slab edge under James Hardie cladding. The base trim comes in 3950 mm lengths, so a longer wall needs more than one length. This jointer goes at each join to conceal it. James Hardie says it can be used where compatible cladding has been fixed to a seasoned timber or light gauge steel frame. Its Matrix Cladding installation guide (October 2026), attached to this page, lists the base trim, this jointer and the matching internal and external corners.\u003c\/p\u003e\u003ch2\u003eInstallation\u003c\/h2\u003e\u003cp\u003eJames Hardie has a separate Hardie Edge installation guide that covers how the trim, jointers and corners are fixed. Follow the current guide from jameshardie.com.au, and check with James Hardie that the trim suits your cladding before ordering. Plan where the joins fall before you fix the base trim, so you know how many jointers you need.\u003c\/p\u003e\u003ch2\u003eCommon questions\u003c\/h2\u003e\u003ch3\u003eWhat does this jointer join?\u003c\/h3\u003e\u003cp\u003eTwo lengths of Hardie Edge Base Trim, end to end. It does not join cladding panels.\u003c\/p\u003e\u003ch3\u003eHow many do I need?\u003c\/h3\u003e\u003cp\u003eOne for each place where two lengths of base trim meet. The base trim is 3950 mm long, so a straight run needs one jointer fewer than it has trim lengths. Corners use James Hardie's separate internal and external corner pieces.\u003c\/p\u003e\u003ch3\u003eIs it sold singly or by the pack?\u003c\/h3\u003e\u003cp\u003eJames Hardie supplies these jointers in packs of 12. Call us on (02) 4605 0215 before ordering to confirm whether the listing is for one jointer or a pack.\u003c\/p\u003e\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\u003cp\u003eYes. Pick up from our yard at 10 Lancaster Street, Ingleburn, or have it delivered across Sydney with the rest of your cladding order.\u003c\/p\u003e","brand":"Alpha Timber","offers":[{"title":"Default Title","offer_id":47796634157367,"sku":"305912","price":9.3,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/HardieEdge-Base-Trim-Jointer.jpg?v=1766025091"}],"url":"https:\/\/alphatimber.com.au\/collections\/james-hardie.oembed","provider":"ALPHA TIMBER","version":"1.0","type":"link"}