{"title":"Cladding","description":"\u003cp\u003eFibre cement and weatherboard cladding in one list: James Hardie FineTex, Axon, Linea and HardiePlank, EZYGroove and EZYPlank, flashings, corners, sealant, wall wrap and fixings.\u003c\/p\u003e","products":[{"product_id":"wall-wrap-breather","title":"Wall wrap breather 1350 mm, breathable building wrap, 30 or 60 m roll","description":"\u003cp\u003eThis is a 1350 mm wide wall wrap breather, a breathable building wrap sold in 30 m and 60 m rolls. It is fixed over the outside of the wall frame before the cladding goes on, as a second line of defence against water that gets past the cladding.\u003c\/p\u003e\u003ch2\u003eKey facts\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eWidth: 1350 mm\u003c\/li\u003e\n\u003cli\u003eRoll lengths: 30 m and 60 m\u003c\/li\u003e\n\u003cli\u003eCoverage: 40.5 m² (30 m roll) and 81 m² (60 m roll), before overlaps\u003c\/li\u003e\n\u003cli\u003eWeight: about 4.3 kg (30 m roll) and 8.6 kg (60 m roll)\u003c\/li\u003e\n\u003cli\u003eType: breather wall wrap, as named by the supplier, with Alpha Timber print\u003c\/li\u003e\n\u003cli\u003eMaterial, vapour permeance class, water barrier rating and flammability index: not listed online yet. Call us on (02) 4605 0215\u003c\/li\u003e\n\u003cli\u003eSold as: single roll\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\u003cp\u003eWrapping timber or steel wall frames behind cladding such as weatherboards, fibre cement sheet and brick veneer. A breather wrap is meant to keep out liquid water from outside while letting water vapour from inside the wall escape. If your plans or energy report name a vapour permeance class, or the site has a bushfire attack level (BAL), check that this wrap meets it before you buy.\u003c\/p\u003e\u003ch2\u003eInstallation\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRun the wrap horizontally, starting at the bottom of the wall, so each higher run laps over the one below and water sheds outwards.\u003c\/li\u003e\n\u003cli\u003eLap sizes, fixings and taping follow the wrap's instructions and AS 4200.2.\u003c\/li\u003e\n\u003cli\u003ePull it taut and fix it to the studs. Tape joins, tears and the gaps around pipes and cables with a tape that suits the wrap.\u003c\/li\u003e\n\u003cli\u003eFit flashings at windows, doors and the bottom of the wall as your plans show.\u003c\/li\u003e\n\u003cli\u003eGet the cladding on soon after wrapping. Do not leave the wrap open to sun and weather for long.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eCommon questions\u003c\/h2\u003e\u003ch3\u003eHow much wall does a roll cover?\u003c\/h3\u003e\u003cp\u003eA 30 m roll is 40.5 m² and a 60 m roll is 81 m², before overlaps. Allow extra for the laps. As an example, a 150 mm lap uses about 11 per cent of each run.\u003c\/p\u003e\u003ch3\u003eWhat vapour permeance class is it?\u003c\/h3\u003e\u003cp\u003eThat is not listed online yet. Call (02) 4605 0215 and we will read the roll label for you before you order.\u003c\/p\u003e\u003ch3\u003eCan I use it under a roof?\u003c\/h3\u003e\u003cp\u003eIt is sold as a wall wrap. Ask us for roof sarking if you are wrapping a roof.\u003c\/p\u003e\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\u003cp\u003eYes. Pick up from our store at 10 Lancaster Street, Ingleburn, or add it to a timber delivery anywhere in Sydney. A roll is 1350 mm long and fits in most cars.\u003c\/p\u003e","brand":"Alpha Timber","offers":[{"title":"30m","offer_id":47896283971895,"sku":"2111","price":69.99,"currency_code":"AUD","in_stock":true},{"title":"60m","offer_id":50241238434103,"sku":"692268","price":134.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/Wall-Wrap-Breather-1350mm.png?v=1766393546"},{"product_id":"blue-board-fiber-cement-sheeting","title":"Blueboard fibre cement sheet 7.5mm, 2440 to 3000 x 1200mm","description":"\u003cp\u003eBlueboard is a 7.5 mm fibre cement sheet with a blue sealed face, sold here in 2440 x 1200, 2725 x 1200 and 3000 x 1200 mm sheets. It is an exterior wall sheet used as the base for render and texture coating finishes.\u003c\/p\u003e\u003ch2\u003eKey facts\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eThickness: 7.5 mm\u003c\/li\u003e\n\u003cli\u003eSheet sizes: 2440 x 1200, 2725 x 1200 and 3000 x 1200 mm\u003c\/li\u003e\n\u003cli\u003eMaterial: fibre cement with a blue sealed face\u003c\/li\u003e\n\u003cli\u003eCoverage: 2.93 m², 3.27 m² and 3.6 m² per sheet\u003c\/li\u003e\n\u003cli\u003eWeight: about 29.6 kg, 33 kg and 36.4 kg per sheet, or about 10 kg per square metre\u003c\/li\u003e\n\u003cli\u003eSold as: single sheets\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eExternal walls finished with render or texture coatings\u003c\/li\u003e\n\u003cli\u003eExtensions, granny flats and renovation cladding\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFix over sarking or wall wrap. Stud spacing, fixings and fixing centres come from the sheet maker's installation guide.\u003c\/li\u003e\n\u003cli\u003eSet the joints and coat the wall with a render or texture system made for fibre cement. Follow the coating maker's instructions for jointing and control joints.\u003c\/li\u003e\n\u003cli\u003eCarry sheets on edge. Store them flat, dry and off the ground.\u003c\/li\u003e\n\u003cli\u003eCut with a fibre cement blade or a score-and-snap tool, outdoors where possible. Wear a P2 dust mask, as the dust contains silica.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eAsk us if you need the installation guide for your job. For anything structural or fire rated, check with your building designer or engineer.\u003c\/p\u003e\u003ch2\u003eCommon questions\u003c\/h2\u003e\u003ch3\u003eHow heavy is a sheet of blueboard?\u003c\/h3\u003e\u003cp\u003eAbout 29.6 kg for a 2440 x 1200 sheet, 33 kg for 2725 x 1200 and 36.4 kg for 3000 x 1200. Plan on two people to carry and fix the larger sheets.\u003c\/p\u003e\u003ch3\u003eHow many sheets do I need?\u003c\/h3\u003e\u003cp\u003eDivide the wall area by the sheet coverage: 2.93 m² for 2440 x 1200, 3.27 m² for 2725 x 1200 or 3.6 m² for 3000 x 1200. Allow extra for cuts around windows and doors.\u003c\/p\u003e\u003ch3\u003eCan blueboard be left uncoated?\u003c\/h3\u003e\u003cp\u003eNo. Blueboard is a base sheet. It is made to be finished with a render or texture coating system, so plan the coating as part of the job and follow the coating maker's timing.\u003c\/p\u003e\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\u003cp\u003eYes. Pick up from our store at 10 Lancaster Street, Ingleburn (Mon–Fri 6am–4pm, Sat 6am–3pm), or have it delivered across Greater Sydney. Call (02) 4605 0215 for a delivery price.\u003c\/p\u003e","brand":"Alpha Timber","offers":[{"title":"2440 x 1200 x 7.5mm","offer_id":47896283021623,"sku":"10677","price":58.0,"currency_code":"AUD","in_stock":true},{"title":"2725 x 1200 7.5mm","offer_id":47896539300151,"sku":"201158","price":65.0,"currency_code":"AUD","in_stock":true},{"title":"3000 x 1200 7.5mm","offer_id":47896539332919,"sku":"201159","price":71.28,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/files\/blueboard-fibre-cement-sheet-alpha-timber.png?v=1795073377"},{"product_id":"hardieplank-smooth-cladding","title":"James Hardie HardiePlank smooth weatherboard 7.5mm, 230 and 300mm","description":"\u003cp\u003eHardiePlank is James Hardie's 7.5 mm fibre cement weatherboard, sold here in the smooth finish as 4200 x 230 mm and 4200 x 300 mm boards. The boards are lapped and fixed across timber or light steel wall frames as external cladding, then painted. James Hardie now writes the name as Hardie Plank Weatherboard.\u003c\/p\u003e\u003ch2\u003eKey facts\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eThickness: 7.5 mm\u003c\/li\u003e\n\u003cli\u003eBoard sizes: 4200 x 230 mm and 4200 x 300 mm\u003c\/li\u003e\n\u003cli\u003eFinish: smooth\u003c\/li\u003e\n\u003cli\u003eMaterial: fibre cement\u003c\/li\u003e\n\u003cli\u003eWeight: about 11.2 kg per 230 mm board and 14.6 kg per 300 mm board\u003c\/li\u003e\n\u003cli\u003eCover: at a 25 mm lap, about 205 mm per row for the 230 mm board and 275 mm for the 300 mm board\u003c\/li\u003e\n\u003cli\u003eSold as: single boards\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\u003cp\u003eExternal wall cladding with a weatherboard look. James Hardie's specification covers ground level and upper storey extensions, gable ends and feature walls, on timber or light gauge steel framing.\u003c\/p\u003e\u003ch2\u003eInstallation\u003c\/h2\u003e\u003cp\u003eThese points come from James Hardie's External Cladding Technical Specification (September 2025), attached to this page.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eStud spacing depends on the wind class and the board width. It is 600 mm maximum in the lowest wind classes and closer as the wind class rises. Check Table 4 of the specification for your site.\u003c\/li\u003e\n\u003cli\u003eTimber frames: 2.8 x 50 mm fibre cement nails by hand, or 2.5 x 50 mm ring shank galvanised coil nails by gun. Steel frames: 41 mm Hardie Drive screws.\u003c\/li\u003e\n\u003cli\u003eKeep fasteners at least 20 mm in from the board ends, and pre-drill there.\u003c\/li\u003e\n\u003cli\u003eEnd joints: on a stud with a 3 mm gap for sealant, or off the stud with a PVC smooth jointer or a metal soaker. Stagger joints over two or more stud lines. Within 1 km of the shoreline, James Hardie does not recommend metal soakers or stud clips.\u003c\/li\u003e\n\u003cli\u003eKeep at least 150 mm clearance to the ground and 50 mm to roofs, decks, paths, steps and driveways.\u003c\/li\u003e\n\u003cli\u003ePaint within 90 days of installation.\u003c\/li\u003e\n\u003cli\u003eFibre cement dust contains silica. Cut outdoors by score and snap, hand guillotine, fibreshear or a dust-reducing saw with an M class vacuum. Wear a respirator, and never use a grinder or dry sweep the dust.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eFollow the current James Hardie specification for the full detail. For bracing, fire rated walls or anything structural, check with your building designer or engineer.\u003c\/p\u003e\u003ch2\u003eCommon questions\u003c\/h2\u003e\u003ch3\u003eHow many boards do I need?\u003c\/h3\u003e\u003cp\u003eAt a 25 mm lap, a 4200 x 230 mm board covers about 0.86 m² of wall and a 4200 x 300 mm board about 1.15 m². Divide your wall area by that figure and add an allowance for offcuts around windows and doors. Confirm the lap for your job from the specification.\u003c\/p\u003e\u003ch3\u003eDoes HardiePlank need painting?\u003c\/h3\u003e\u003cp\u003eYes. James Hardie says its external cladding must be painted within 90 days of installation.\u003c\/p\u003e\u003ch3\u003eCan I gun nail it?\u003c\/h3\u003e\u003cp\u003eJames Hardie lists 2.5 x 50 mm ring shank galvanised coil nails for gun nailing to timber frames. Set the gun so the heads finish flush with the board.\u003c\/p\u003e\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\u003cp\u003eYes. Pick up from our store at 10 Lancaster Street, Ingleburn, or ask us about delivery across Sydney. Call (02) 4605 0215 to check stock. The boards are 4.2 m long, so bring racks, a long tray or a trailer.\u003c\/p\u003e","brand":"James Hardie","offers":[{"title":"4200x230x7.5mm","offer_id":47896282202423,"sku":"400265","price":34.99,"currency_code":"AUD","in_stock":false},{"title":"4200x300x7.5mm","offer_id":47896536416567,"sku":"400266","price":44.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/HardiePlank-Smooth-Cladding.png?v=1766025348"},{"product_id":"james-hardie-finetex-cladding","title":"James Hardie Fine Texture cladding 8.5mm fibre cement panel","description":"\u003cp\u003eHardie Fine Texture cladding (also sold as FineTex) is an 8.5 mm James Hardie fibre cement panel with a fine sand texture embedded in the face and a shiplap V-joint on the long edges. It is fixed vertically to framed walls and painted on site to give a rendered look without rendering.\u003c\/p\u003e\n\u003ch2\u003eKey facts\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eThickness: 8.5 mm\u003c\/li\u003e\n\u003cli\u003eSizes: 2440 x 1200 mm, 2750 x 1200 mm, 3000 x 1200 mm and 3600 x 1200 mm\u003c\/li\u003e\n\u003cli\u003eMaterial: fibre cement with an embedded fine texture, pre-sealed\u003c\/li\u003e\n\u003cli\u003eEdges: shiplap V-joint on the long edges\u003c\/li\u003e\n\u003cli\u003eWeight (James Hardie, approximate): 38 kg (2440), 43 kg (2750), 47 kg (3000), 56 kg (3600). About 13 kg per m²\u003c\/li\u003e\n\u003cli\u003eCoverage per panel: 2.93 m², 3.3 m², 3.6 m² and 4.32 m²\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eThe size shown as 2745 x 1200 mm in the size list is James Hardie's 2750 x 1200 mm panel.\u003c\/p\u003e\n\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\n\u003cp\u003eExternal wall cladding on residential buildings, over a seasoned timber or light gauge steel frame. James Hardie's guide covers direct fixing to timber frames, or fixing over cavity battens on timber or steel frames.\u003c\/p\u003e\n\u003ch2\u003eInstallation\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003ePanels run vertically. Maximum stud or batten spacing is 600 mm for wind classes N1 to N4, 450 mm for N5 and 300 mm for N6.\u003c\/li\u003e\n\u003cli\u003eRun a bead of joint sealant on the shiplap edge and use foam back sealing tape behind vertical joins, as shown in the guide.\u003c\/li\u003e\n\u003cli\u003eKeep at least 150 mm clearance to the ground and 50 mm from roofs, decks, paths and driveways.\u003c\/li\u003e\n\u003cli\u003eJames Hardie says no primer is needed. Finish with an exterior acrylic paint.\u003c\/li\u003e\n\u003cli\u003eFibre cement dust contains silica. Cut with a dust-reducing saw and vacuum extraction, wear a P2 respirator, and never use a grinder or dry sweep the dust.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eFollow the current James Hardie installation guide for framing, fixings and weatherproofing. For bushfire zones, fire rated walls or anything structural, check the James Hardie documents and your building designer or engineer.\u003c\/p\u003e\n\u003ch2\u003eCommon questions\u003c\/h2\u003e\n\u003ch3\u003eIs Fine Texture the same as FineTex?\u003c\/h3\u003e\n\u003cp\u003eYes. FineTex is the short name used in our system for Hardie Fine Texture cladding.\u003c\/p\u003e\n\u003ch3\u003eHow heavy is a panel?\u003c\/h3\u003e\n\u003cp\u003eJames Hardie lists about 38 kg for a 2440 x 1200 panel, 43 kg for 2750, 47 kg for 3000 and 56 kg for 3600. Plan on two people to carry and fix them.\u003c\/p\u003e\n\u003ch3\u003eDoes it need rendering or priming?\u003c\/h3\u003e\n\u003cp\u003eNo. The texture is already in the face of the panel and James Hardie says no primer is needed. It is painted on site with exterior acrylic paint.\u003c\/p\u003e\n\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\n\u003cp\u003eYes. Pick up from our store at 10 Lancaster Street, Ingleburn, or ask us about delivery across Sydney. Call (02) 4605 0215 to check stock on the size you need.\u003c\/p\u003e","brand":"James Hardie","offers":[{"title":"2440x1200mm","offer_id":50222019969335,"sku":"405252","price":133.31,"currency_code":"AUD","in_stock":true},{"title":"2745x1200mm","offer_id":47896282136887,"sku":"405255","price":149.54,"currency_code":"AUD","in_stock":true},{"title":"3000x1200mm","offer_id":47896536351031,"sku":"405253","price":163.7,"currency_code":"AUD","in_stock":true},{"title":"3600x1200mm","offer_id":47896536383799,"sku":"405254","price":196.37,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/James-Hardie-FineTex-Cladding.png?v=1766108968"},{"product_id":"james-hardie-axon-cladding","title":"James Hardie Axon cladding 9mm, 133 and 400 groove panels","description":"\u003cp\u003eJames Hardie Axon cladding is a 9 mm pre-primed fibre cement panel with vertical grooves that give the look of vertical joint timber. The number in the name is the groove spacing: Axon 133 has grooves 133 mm apart and Axon 400 has grooves 400 mm apart.\u003c\/p\u003e\n\u003ch2\u003eKey facts\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eThickness: 9 mm\u003c\/li\u003e\n\u003cli\u003ePanel width: 1200 mm\u003c\/li\u003e\n\u003cli\u003eAxon 133 Smooth: 2450, 2750, 3000 and 3600 mm long\u003c\/li\u003e\n\u003cli\u003eAxon 133 Grained (timber-look texture): 3000 mm long\u003c\/li\u003e\n\u003cli\u003eAxon 400 Smooth: 2450, 2750 and 3000 mm long\u003c\/li\u003e\n\u003cli\u003eMaterial: fibre cement, pre-primed\u003c\/li\u003e\n\u003cli\u003eEdges: stepped shiplap joint on the long edges\u003c\/li\u003e\n\u003cli\u003eWeight (James Hardie): 38.1 kg (2450), 42.8 kg (2750), 46.7 kg (3000), 56 kg (3600)\u003c\/li\u003e\n\u003cli\u003eCoverage per panel: 2.94 m² (2450), 3.3 m² (2750), 3.6 m² (3000), 4.32 m² (3600)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\n\u003cp\u003eExternal wall cladding on houses, fixed over a seasoned timber or light gauge steel wall frame. It can be fixed direct to the frame or over cavity battens. James Hardie also publishes a technical supplement for using Axon on interior walls.\u003c\/p\u003e\n\u003ch2\u003eInstallation\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003ePanels run vertically. Maximum stud or batten spacing is 600 mm for wind classes N1 to N4, 450 mm for N5 and 300 mm for N6.\u003c\/li\u003e\n\u003cli\u003eRun a bead of joint sealant on the shiplap edge and use foam back sealing tape under vertical joints, as shown in the guide.\u003c\/li\u003e\n\u003cli\u003eKeep at least 150 mm clearance to the ground and 50 mm from roofs, decks, paths and driveways.\u003c\/li\u003e\n\u003cli\u003ePaint within 3 months of fixing, or within 7 days if the site is within 1 km of the coast.\u003c\/li\u003e\n\u003cli\u003eFibre cement dust contains silica. Cut with a dust-reducing saw and vacuum extraction, wear a P2 respirator, and never use a grinder, dry sweep the dust or run a power saw indoors.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eFollow the current James Hardie Axon Cladding installation guide for framing, fixings and weatherproofing. For bracing, fire rated walls or anything structural, check with your building designer or engineer.\u003c\/p\u003e\n\u003ch2\u003eCommon questions\u003c\/h2\u003e\n\u003ch3\u003eWhat is the difference between Axon 133 and Axon 400?\u003c\/h3\u003e\n\u003cp\u003eThe groove spacing. Axon 133 has a groove every 133 mm for a narrow board look. Axon 400 has a groove every 400 mm for a wide board look. Axon 133 also comes in a Grained finish with a timber-look texture.\u003c\/p\u003e\n\u003ch3\u003eHow heavy is an Axon panel?\u003c\/h3\u003e\n\u003cp\u003eJames Hardie lists 38.1 kg for a 2450 mm panel, 42.8 kg for 2750 mm, 46.7 kg for 3000 mm and 56 kg for 3600 mm. Plan on two people to carry and fix them.\u003c\/p\u003e\n\u003ch3\u003eDoes Axon need painting?\u003c\/h3\u003e\n\u003cp\u003eYes. The panels come pre-primed and are painted on site. James Hardie says to paint within 3 months of fixing, or within 7 days near the coast.\u003c\/p\u003e\n\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\n\u003cp\u003eYes. Pick up from our store at 10 Lancaster Street, Ingleburn, or ask us about delivery across Sydney. Call (02) 4605 0215 to check stock on the size and finish you need.\u003c\/p\u003e","brand":"James Hardie","offers":[{"title":"2450x1200x133mm Smooth","offer_id":47896282104119,"sku":"403931","price":156.0,"currency_code":"AUD","in_stock":true},{"title":"2750x1200x133mm Smooth","offer_id":47896536187191,"sku":"403932","price":168.3,"currency_code":"AUD","in_stock":true},{"title":"3000x1200x133mm Smooth","offer_id":47896536252727,"sku":"403933","price":183.4,"currency_code":"AUD","in_stock":true},{"title":"3600x1200x133mm Smooth","offer_id":47896536285495,"sku":"404979","price":223.82,"currency_code":"AUD","in_stock":true},{"title":"3000x1200x133mm Grained","offer_id":50221986971959,"sku":"404512","price":207.0,"currency_code":"AUD","in_stock":false},{"title":"2450x1200x400mm Smooth","offer_id":47896536154423,"sku":"404417","price":155.0,"currency_code":"AUD","in_stock":true},{"title":"2750x1200x400mm Smooth","offer_id":47896536219959,"sku":"404418","price":168.3,"currency_code":"AUD","in_stock":false},{"title":"3000x1200x400mm Smooth","offer_id":50221741965623,"sku":"404419","price":186.5,"currency_code":"AUD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/James-Hardie-Axon-Cladding.png?v=1766107217"},{"product_id":"james-hardie-finetex-9mm-aluminium-rec-horizontal-flashing-3-0m","title":"James Hardie 9mm aluminium horizontal express jointer 3000mm","description":"\u003cp\u003eThe Hardie 9mm aluminium horizontal express jointer is a 3000 mm aluminium jointer for the horizontal joints in James Hardie panel cladding. James Hardie describes it as a horizontal jointer that creates a 6 mm horizontal shadow line while concealing the edge of the bottom panels.\u003c\/p\u003e\u003ch2\u003eKey facts\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eBrand: James Hardie, product code 306104\u003c\/li\u003e\n\u003cli\u003eLength: 3000 mm (3.0 m)\u003c\/li\u003e\n\u003cli\u003eMaterial: aluminium\u003c\/li\u003e\n\u003cli\u003eShadow line: 6 mm, horizontal\u003c\/li\u003e\n\u003cli\u003eListed for: Hardie Fine Texture Cladding and Hardie Brushed Concrete Cladding\u003c\/li\u003e\n\u003cli\u003eJoining: James Hardie lists a matching connector (code 306110) for joining lengths\u003c\/li\u003e\n\u003cli\u003eSold as: single length\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\u003cp\u003eHorizontal joints where one row of panels sits above another, on walls clad in \u003ca href=\"\/products\/james-hardie-finetex-cladding\"\u003eHardie Fine Texture cladding\u003c\/a\u003e (FineTex) or Hardie Brushed Concrete cladding. It is a cladding accessory, not a roof flashing. James Hardie also makes a separate recessed horizontal jointer (code 306190). This listing is the express jointer, code 306104. For the other edges of the wall, see the \u003ca href=\"\/products\/james-hardie-finetex-9mm-aluminium-rec-base-trim-flashing-3-0m\"\u003e9mm base trim\u003c\/a\u003e and the \u003ca href=\"\/products\/james-hardie-finetex-9mm-aluminium-external-slimline-corner-3-0m\"\u003e9mm external slimline corner\u003c\/a\u003e.\u003c\/p\u003e\u003ch2\u003eInstallation\u003c\/h2\u003e\u003cp\u003eFollow the Hardie Fine Texture Cladding and Hardie Brushed Concrete Cladding installation guide (September 2026), listed under this product's documents. Its steps say to apply a continuous 4 mm bead of Hardie Joint Sealant to the edge of the panel, then install the horizontal jointer. Where slimline corners are used, the horizontal jointer must be cut at 45 degrees. Use the guide's direct fix or cavity fix details for fixing and for the panel above.\u003c\/p\u003e\u003ch2\u003eCommon questions\u003c\/h2\u003e\u003ch3\u003eWhich cladding does it suit?\u003c\/h3\u003e\u003cp\u003eIt is listed in James Hardie's installation guide for Hardie Fine Texture Cladding and Hardie Brushed Concrete Cladding.\u003c\/p\u003e\u003ch3\u003eHow many lengths do I need?\u003c\/h3\u003e\u003cp\u003eJames Hardie's rule is the total length of horizontal joints divided by 3000 mm. Round up, and allow extra for offcuts at corners.\u003c\/p\u003e\u003ch3\u003eHow are lengths joined?\u003c\/h3\u003e\u003cp\u003eJames Hardie lists a horizontal express connector (code 306110) for joining lengths. Call (02) 4605 0215 to check stock of the connector.\u003c\/p\u003e\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\u003cp\u003eYes. Pick up from our store at 10 Lancaster Street, Ingleburn, or have it delivered across Sydney with the rest of your order. Call (02) 4605 0215 to check stock.\u003c\/p\u003e","brand":"James Hardie","offers":[{"title":"Default Title","offer_id":47748426498359,"sku":"306104","price":38.1,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/FineTex-9mm-Alu-Rec-Horizontal-Flashing-3.0m.png?v=1766108804"},{"product_id":"james-hardie-finetex-9mm-aluminium-rec-base-trim-flashing-3-0m","title":"James Hardie 9mm aluminium base trim 3000mm","description":"\u003cp\u003eThe Hardie 9mm aluminium base trim is a 3000 mm aluminium trim that finishes the bottom edge of James Hardie panel cladding. It suits 8.5 to 9 mm thick cladding panels and creates a shadow line over a slab edge or a balcony edge.\u003c\/p\u003e\u003ch2\u003eKey facts\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eBrand: James Hardie, product code 306105\u003c\/li\u003e\n\u003cli\u003eLength: 3000 mm (3.0 m)\u003c\/li\u003e\n\u003cli\u003eMaterial: aluminium\u003c\/li\u003e\n\u003cli\u003eSuits cladding panels 8.5 to 9 mm thick\u003c\/li\u003e\n\u003cli\u003eFinish: ready to paint after installation\u003c\/li\u003e\n\u003cli\u003eJoining: James Hardie lists a matching base trim connector (code 306111) for joining lengths\u003c\/li\u003e\n\u003cli\u003eSold as: single length\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\u003cp\u003eThe bottom edge of walls clad in 8.5 to 9 mm James Hardie panels, such as \u003ca href=\"\/products\/james-hardie-finetex-cladding\"\u003eHardie Fine Texture cladding\u003c\/a\u003e (FineTex) and Hardie Brushed Concrete cladding. James Hardie's guide describes it as a trim to cover slab edges, or a detail under balconies and cantilevers, and says the base trim option may hide a poor quality slab edge. For the corners, see the \u003ca href=\"\/products\/james-hardie-finetex-9mm-aluminium-external-slimline-corner-3-0m\"\u003e9mm external slimline corner\u003c\/a\u003e and the \u003ca href=\"\/products\/james-hardie-external-corner-3-0m\"\u003e9mm external square corner\u003c\/a\u003e.\u003c\/p\u003e\u003ch2\u003eInstallation\u003c\/h2\u003e\u003cp\u003eFollow the Hardie Fine Texture Cladding and Hardie Brushed Concrete Cladding installation guide (September 2026), listed under this product's documents. The corner accessories go on first, and the base trim then slides into them. Where slimline corners are used, James Hardie's cavity fix steps say to cut the base flashing at 45 degrees. Keep the cladding at least 150 mm clear of the ground and 50 mm clear of roofs, decks, paths, steps and driveways. Where the exposed slab edge is part of the termite barrier, at least 75 mm of the slab edge must stay visible. The trim is ready to paint, so paint it with the wall.\u003c\/p\u003e\u003ch2\u003eCommon questions\u003c\/h2\u003e\u003ch3\u003eWhich cladding does it suit?\u003c\/h3\u003e\u003cp\u003eCladding panels 8.5 to 9 mm thick. It is listed in James Hardie's installation guide for Hardie Fine Texture Cladding and Hardie Brushed Concrete Cladding.\u003c\/p\u003e\u003ch3\u003eHow many lengths do I need?\u003c\/h3\u003e\u003cp\u003eEach length is 3000 mm. Measure the run along the bottom of the clad walls, divide by 3.0 and round up. Allow extra for offcuts at corners.\u003c\/p\u003e\u003ch3\u003eHow are lengths joined?\u003c\/h3\u003e\u003cp\u003eJames Hardie lists a base trim connector (code 306111) for joining lengths. Call (02) 4605 0215 to check stock of the connector.\u003c\/p\u003e\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\u003cp\u003eYes. Pick up from our store at 10 Lancaster Street, Ingleburn, or have it delivered across Sydney with the rest of your order. Call (02) 4605 0215 to check stock.\u003c\/p\u003e","brand":"James Hardie","offers":[{"title":"Default Title","offer_id":47748426236215,"sku":"306105","price":59.51,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/FineTex-9mm-Alu-Rec-Base-Trim-Flashing-3.0m.png?v=1766108634"},{"product_id":"james-hardie-scyon-linea-16mm-aluminium-internal-corner-mould-3-6m","title":"James Hardie Linea 16mm aluminium internal corner mould 3600mm","description":"\u003cp\u003eThis is the James Hardie Linea 16 mm aluminium internal corner mould, a 3600 mm long aluminium extrusion that forms the internal corners on Linea Weatherboard walls. It is supplied ready to paint and gives a straight, clean line where two clad walls meet.\u003c\/p\u003e\u003ch2\u003eKey facts\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLength: 3600 mm\u003c\/li\u003e\n\u003cli\u003eMaterial: aluminium extrusion, internal corner profile\u003c\/li\u003e\n\u003cli\u003eFinish: ready to paint after installation\u003c\/li\u003e\n\u003cli\u003eMade for: James Hardie Linea Weatherboard (16 mm), internal corners\u003c\/li\u003e\n\u003cli\u003eWeight: about 1.4 kg per length\u003c\/li\u003e\n\u003cli\u003eJames Hardie product code: 305511\u003c\/li\u003e\n\u003cli\u003eSold as: single 3600 mm length\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\u003cp\u003eIt finishes the inside corners of a wall clad in Linea Weatherboard. The boards stop at the corner mould, so the corner reads as one straight line from top to bottom. James Hardie's product page lists it for Linea Weatherboard and for Stria Cladding. For Stria walls, see also the \u003ca href=\"\/products\/james-hardie-aluminium-internal-corner-3m\"\u003e14 mm aluminium internal corner\u003c\/a\u003e. For the outside corners of a Linea wall, see the \u003ca href=\"\/products\/james-hardie-scyon-linea-aluminium-external-slimline-boxed-corner-3-6m\"\u003eLinea external slimline boxed corner\u003c\/a\u003e.\u003c\/p\u003e\u003ch2\u003eInstallation\u003c\/h2\u003e\u003cp\u003eJames Hardie's Linea Weatherboard installation guide sets out the corner detail. In short: frame the corner with double studs, fit the corner mould with 40 mm nails at 400 mm vertical centres in both flanges, then install the boards leaving a nominal 2 mm gap to the aluminium corner. Where two lengths join, and at floor level, overlap by 50 mm with the upper section over the lower one. Follow the current guide for the full detail, and paint the corner with the wall.\u003c\/p\u003e\u003ch2\u003eCommon questions\u003c\/h2\u003e\u003ch3\u003eWhich cladding does this corner suit?\u003c\/h3\u003e\u003cp\u003eIt is made for 16 mm Linea Weatherboard. James Hardie also lists it for Stria Cladding. If you are using Axon or another Hardie cladding, ask us for the corner made for that product.\u003c\/p\u003e\u003ch3\u003eHow many do I need?\u003c\/h3\u003e\u003cp\u003eAdd up the height of every internal corner and divide by 3600 mm. Round up to whole lengths, and allow for the 50 mm overlap wherever two lengths join.\u003c\/p\u003e\u003ch3\u003eDoes it come painted?\u003c\/h3\u003e\u003cp\u003eNo. It is supplied ready to paint and is painted on site after installation.\u003c\/p\u003e\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\u003cp\u003eYes. Pick up from our store at 10 Lancaster Street, Ingleburn, or have it delivered across Sydney. Call (02) 4605 0215 for a delivery quote. At 3.6 m long it needs racks, a long tray or a trailer.\u003c\/p\u003e","brand":"James Hardie","offers":[{"title":"Default Title","offer_id":47748425449783,"sku":"305511","price":109.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/Scyon-Linea-James-Hardie-16mm-Aluminium-Internal-Corner_Mould_3.6m.png?v=1766110778"},{"product_id":"james-hardie-scyon-linea-aluminium-external-slimline-boxed-corner-3-6m","title":"James Hardie Linea aluminium external slimline boxed corner 3600mm","description":"\u003cp\u003eThis is the James Hardie Linea aluminium external slimline boxed corner, a 3600 mm long aluminium extrusion that forms the external corners on Linea Weatherboard walls. It is supplied ready to paint and gives a straight, boxed corner where the weatherboards end.\u003c\/p\u003e\u003ch2\u003eKey facts\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLength: 3600 mm\u003c\/li\u003e\n\u003cli\u003eMaterial: aluminium extrusion, slimline boxed profile\u003c\/li\u003e\n\u003cli\u003eFinish: ready to paint after installation\u003c\/li\u003e\n\u003cli\u003eMade for: James Hardie Linea Weatherboard, external corners\u003c\/li\u003e\n\u003cli\u003eWeight: about 2 kg per length\u003c\/li\u003e\n\u003cli\u003eJames Hardie product code: 305512\u003c\/li\u003e\n\u003cli\u003eSold as: single 3600 mm length\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\u003cp\u003eIt finishes the outside corners of a wall clad in Linea Weatherboard. The boards stop at the corner piece, so the corner reads as one straight line from top to bottom. James Hardie lists it for Linea Weatherboard only. Other Hardie claddings have their own corner accessories.\u003c\/p\u003e\u003ch2\u003eInstallation\u003c\/h2\u003e\u003cp\u003eJames Hardie's Linea Weatherboard installation guide sets out the corner detail. In short: run the weather barrier continuously around the corner, fix the boxed corner with 40 mm fibre cement nails in the indentation provided, at 400 mm vertical centres through both flanges, then install the boards leaving a nominal 2 mm gap to the aluminium corner. On a cavity fix, the battens go on before the corner. James Hardie also lists caps to seal the bottom of the corner. Follow the current guide for the full detail, and paint the corner with the wall.\u003c\/p\u003e\u003ch2\u003eCommon questions\u003c\/h2\u003e\u003ch3\u003eWhich cladding does this corner suit?\u003c\/h3\u003e\u003cp\u003eJames Hardie lists it for Linea Weatherboard. If you are using Stria, Axon or another Hardie cladding, ask us for the corner made for that product.\u003c\/p\u003e\u003ch3\u003eHow many do I need?\u003c\/h3\u003e\u003cp\u003eJames Hardie's rule is wall height multiplied by the number of external corners, divided by 3600 mm. Round up to whole lengths.\u003c\/p\u003e\u003ch3\u003eDoes it come painted?\u003c\/h3\u003e\u003cp\u003eNo. It is supplied ready to paint and is painted on site after installation.\u003c\/p\u003e\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\u003cp\u003eYes. Pick up from our store at 10 Lancaster Street, Ingleburn, or have it delivered across Sydney. Call (02) 4605 0215 for a delivery quote. At 3.6 m long it needs racks, a long tray or a trailer.\u003c\/p\u003e","brand":"James Hardie","offers":[{"title":"Default Title","offer_id":47748424007991,"sku":"305512","price":164.95,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/Scyon-Linea-Aluminium-External-Slimline-Boxed-Corner-3.6m.png?v=1766110946"},{"product_id":"james-hardie-linea-cladding","title":"James Hardie Linea Weatherboard 16mm, 4200 x 150mm fibre cement","description":"\u003cp\u003eLinea Weatherboard is James Hardie's 16 mm thick fibre cement weatherboard, sold here as a 4200 x 150 mm board. The pre-primed boards are lapped and fixed across timber or light steel wall frames as external cladding with deep shadow lines, then painted. It was sold before as Scyon Linea.\u003c\/p\u003e\u003ch2\u003eKey facts\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eThickness: 16 mm\u003c\/li\u003e\n\u003cli\u003eBoard size: 4200 x 150 mm (4205 mm overall with the tongue and groove end)\u003c\/li\u003e\n\u003cli\u003eMaterial: fibre cement, pre-primed\u003c\/li\u003e\n\u003cli\u003eEnds: tongue and groove short ends, so boards can join off the stud\u003c\/li\u003e\n\u003cli\u003eWeight: about 2.8 kg per metre, so about 12 kg per board (James Hardie's guide)\u003c\/li\u003e\n\u003cli\u003eCover: at the 30 mm lap, 120 mm per row, about 0.50 m² per board\u003c\/li\u003e\n\u003cli\u003eJames Hardie product code: 403930\u003c\/li\u003e\n\u003cli\u003eSold as: single boards\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\u003cp\u003eExternal wall cladding with a classic narrow weatherboard look. James Hardie's guide covers residential walls over a seasoned timber frame or a light gauge steel frame. For the wider board, see \u003ca href=\"\/products\/scyon-linea-4200x180x16mm\"\u003eLinea Weatherboard 180 mm\u003c\/a\u003e. For corners, see the \u003ca href=\"\/products\/james-hardie-scyon-linea-aluminium-external-slimline-boxed-corner-3-6m\"\u003eLinea external slimline boxed corner\u003c\/a\u003e and the \u003ca href=\"\/products\/james-hardie-scyon-linea-16mm-aluminium-internal-corner-mould-3-6m\"\u003eLinea internal corner mould\u003c\/a\u003e.\u003c\/p\u003e\u003ch2\u003eInstallation\u003c\/h2\u003e\u003cp\u003eThese points come from James Hardie's Linea Weatherboard installation guide (September 2026), attached to this page.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eStud spacing depends on the wind class. It is 600 mm maximum up to N3\/C1, and closer near building edges and in higher wind classes. Check Table 3 of the guide for your site.\u003c\/li\u003e\n\u003cli\u003eLap each board 30 mm over the one below.\u003c\/li\u003e\n\u003cli\u003eTimber frames: face nail with 60 x 3.15 mm bullet head nails, or conceal nail with 40 x 2.8 mm fibre cement nails or Paslode 45 x 2.5 mm ring shank coil nails. Steel frames: 41 mm Hardie Drive screws.\u003c\/li\u003e\n\u003cli\u003eWithin 1 km of the coast, James Hardie calls for class 4 fasteners.\u003c\/li\u003e\n\u003cli\u003eEnd joints are tongue and groove and sit off the stud, at least 100 mm from the side of a stud. Run a continuous bead of Hardie Joint Sealant on the back of the tongue and push the boards firmly together. Keep joints in adjacent rows at least one stud spacing apart.\u003c\/li\u003e\n\u003cli\u003eKeep at least 150 mm clearance to the ground and 50 mm to roofs, decks, paths, steps and driveways.\u003c\/li\u003e\n\u003cli\u003ePaint within 3 months of fixing, or within 7 days if the site is within 1 km of the coast. James Hardie recommends at least two coats of quality exterior acrylic paint.\u003c\/li\u003e\n\u003cli\u003eFibre cement dust contains silica. Cut outdoors with a hand guillotine, fibreshear or a dust-reducing saw with an M class vacuum. Wear a P2 respirator, and never use a grinder or dry sweep the dust.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eFollow the current James Hardie guide for the full detail. For bracing, fire rated walls or anything structural, check with your building designer or engineer.\u003c\/p\u003e\u003ch2\u003eCommon questions\u003c\/h2\u003e\u003ch3\u003eHow many boards do I need?\u003c\/h3\u003e\u003cp\u003eAt the 30 mm lap each row covers 120 mm, so you need about 8.3 rows for every metre of wall height. One 4200 mm board covers about 0.50 m². Divide your wall area by that figure and add an allowance for offcuts around windows and doors.\u003c\/p\u003e\u003ch3\u003eDo the end joints have to land on a stud?\u003c\/h3\u003e\u003cp\u003eNo. The short ends are tongue and groove and are joined off the stud, at least 100 mm from the side of a stud, with sealant on the back of the tongue.\u003c\/p\u003e\u003ch3\u003eDoes Linea need painting?\u003c\/h3\u003e\u003cp\u003eYes. The boards are pre-primed and must be painted within 3 months of being installed, or within 7 days near the coast.\u003c\/p\u003e\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\u003cp\u003eYes. Pick up from our store at 10 Lancaster Street, Ingleburn, or ask us about delivery across Sydney. Call (02) 4605 0215 to check stock. The boards are 4.2 m long, so bring racks, a long tray or a trailer.\u003c\/p\u003e","brand":"James Hardie","offers":[{"title":"Default Title","offer_id":47197296492855,"sku":"403930","price":44.55,"currency_code":"AUD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/Linea-4200x150x16mm.png?v=1766109875"},{"product_id":"james-hardie-easylap-cladding","title":"James Hardie EasyLap panel 8.5mm fibre cement cladding","description":"\u003cp\u003eJames Hardie EasyLap panel is an 8.5 mm pre-primed fibre cement cladding sheet with a shiplap joint along its two long edges. It is fixed vertically to timber or steel framed walls and finished on site with a roll-on textured acrylic paint for a rendered look.\u003c\/p\u003e\n\u003ch2\u003eKey facts\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eThickness: 8.5 mm\u003c\/li\u003e\n\u003cli\u003eSizes: 2440 x 1200 mm, 3000 x 900 mm, 3000 x 1200 mm and 3600 x 1200 mm\u003c\/li\u003e\n\u003cli\u003eMaterial: fibre cement, pre-primed\u003c\/li\u003e\n\u003cli\u003eEdges: shiplap joint on the two long edges\u003c\/li\u003e\n\u003cli\u003eWeight (James Hardie, approximate): 38 kg (2440 x 1200), 35 kg (3000 x 900), 47 kg (3000 x 1200), 56 kg (3600 x 1200). About 13 kg per m²\u003c\/li\u003e\n\u003cli\u003eCoverage per sheet: 2.93 m², 2.7 m², 3.6 m² and 4.32 m²\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\n\u003cp\u003eExternal wall cladding on houses and medium-density residential buildings, including alterations and additions. James Hardie's guide covers fixing direct to the frame or over cavity battens, on timber or light gauge steel framing.\u003c\/p\u003e\n\u003ch2\u003eInstallation\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003ePanels run vertically. Stud or batten spacing depends on the wind class of the site: 600 mm maximum for N1 to N4, closer for higher wind classes.\u003c\/li\u003e\n\u003cli\u003eRun a bead of joint sealant along the shiplap edge and use sealing tape behind vertical joints, as shown in the guide.\u003c\/li\u003e\n\u003cli\u003eKeep at least 150 mm clearance between the bottom of the cladding and the ground.\u003c\/li\u003e\n\u003cli\u003ePaint within 3 months of fixing, or within 7 days if the site is within 1 km of the coast.\u003c\/li\u003e\n\u003cli\u003eFibre cement dust contains silica. Cut outdoors with a dust-reducing saw and vacuum extraction, wear a P2 respirator, and never use a grinder or dry sweep the dust.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eFollow the current James Hardie EasyLap Panel installation guide for framing, fixings and weatherproofing. For anything structural or fire rated, check with your building designer or engineer.\u003c\/p\u003e\n\u003ch2\u003eCommon questions\u003c\/h2\u003e\n\u003ch3\u003eHow heavy is a sheet of EasyLap?\u003c\/h3\u003e\n\u003cp\u003eJames Hardie lists about 38 kg for a 2440 x 1200 sheet, 47 kg for 3000 x 1200 and 56 kg for 3600 x 1200. Plan on two people to carry and fix the larger sheets.\u003c\/p\u003e\n\u003ch3\u003eDoes EasyLap need painting?\u003c\/h3\u003e\n\u003cp\u003eYes. The panel comes pre-primed and is finished on site with a roll-on textured acrylic paint. James Hardie says to paint within 3 months of fixing, or within 7 days near the coast.\u003c\/p\u003e\n\u003ch3\u003eHow many sheets do I need?\u003c\/h3\u003e\n\u003cp\u003eDivide the wall area by the sheet coverage: 2.93 m² for 2440 x 1200, 3.6 m² for 3000 x 1200 and 4.32 m² for 3600 x 1200. Allow extra for offcuts around windows and doors.\u003c\/p\u003e\n\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\n\u003cp\u003eYes. Pick up from our store at 10 Lancaster Street, Ingleburn, or ask us about delivery across Sydney. Call (02) 4605 0215 to check stock on the size you need.\u003c\/p\u003e","brand":"James Hardie","offers":[{"title":"2440x1200x8.5mm","offer_id":47896279810359,"sku":"404184","price":122.98,"currency_code":"AUD","in_stock":true},{"title":"3000x900x8.5mm","offer_id":47896534057271,"sku":"404186","price":121.04,"currency_code":"AUD","in_stock":false},{"title":"3000x1200x8.5mm","offer_id":47896534090039,"sku":"404185","price":151.21,"currency_code":"AUD","in_stock":false},{"title":"3600x1200x8.5mm","offer_id":47896534122807,"sku":"404980","price":191.03,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/James-Hardie-Easylap-Cladding.png?v=1766107704"},{"product_id":"james-hardie-external-corner-3-0m","title":"James Hardie 9mm aluminium external square corner 3000mm","description":"\u003cp\u003eThe Hardie 9mm aluminium external square corner is a 3000 mm aluminium trim that finishes the outside corners of James Hardie panel cladding. It suits cladding panels 8.5 to 9 mm thick and gives 10 mm of coverage over the panel edges.\u003c\/p\u003e\n\u003ch2\u003eKey facts\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eBrand: James Hardie, product code 306100\u003c\/li\u003e\n\u003cli\u003eLength: 3000 mm (3.0 m)\u003c\/li\u003e\n\u003cli\u003eMaterial: aluminium\u003c\/li\u003e\n\u003cli\u003eSuits cladding panels 8.5 to 9 mm thick\u003c\/li\u003e\n\u003cli\u003eCoverage: 10 mm\u003c\/li\u003e\n\u003cli\u003eFinish: ready to paint after installation\u003c\/li\u003e\n\u003cli\u003eWeight: about 1.8 kg per length\u003c\/li\u003e\n\u003cli\u003eSold as: single length\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\n\u003cp\u003eExternal (outside) corners where two walls of 9 mm fibre cement panel cladding meet. James Hardie lists it as compatible with Axon cladding, Hardie Fine Texture cladding and Hardie Brushed Concrete cladding. It covers the cut panel edges and gives a straight, square corner line.\u003c\/p\u003e\n\u003ch2\u003eInstallation\u003c\/h2\u003e\n\u003cp\u003eFit the corner as shown in the James Hardie installation guide for the cladding you are using. The guide sets out the fixing, sealing and clearances for that system. Cut the aluminium with a hacksaw or a fine-tooth metal blade and remove any burrs. Paint it after installation, along with the cladding. For 14 mm cladding, use the \u003ca href=\"\/products\/hardie-14mm-alum-external-corner-3000mm\"\u003eHardie 14mm aluminium external corner\u003c\/a\u003e instead.\u003c\/p\u003e\n\u003ch2\u003eCommon questions\u003c\/h2\u003e\n\u003ch3\u003eWhich cladding does this corner suit?\u003c\/h3\u003e\n\u003cp\u003ePanels 8.5 to 9 mm thick. James Hardie lists Axon, Hardie Fine Texture and Hardie Brushed Concrete cladding.\u003c\/p\u003e\n\u003ch3\u003eHow many lengths do I need?\u003c\/h3\u003e\n\u003cp\u003eEach length is 3000 mm. A wall up to 3.0 m high needs one length per external corner. Allow extra for taller walls and offcuts.\u003c\/p\u003e\n\u003ch3\u003eDoes it come painted?\u003c\/h3\u003e\n\u003cp\u003eNo colour finish is stated by James Hardie. It is described as ready to paint after installation, so paint it with the cladding.\u003c\/p\u003e\n\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\n\u003cp\u003eYes. Pick up from our store at 10 Lancaster Street, Ingleburn, or have it delivered across Sydney with the rest of your order. Call (02) 4605 0215 to check stock.\u003c\/p\u003e","brand":"James Hardie","offers":[{"title":"Default Title","offer_id":47748419977527,"sku":"306100","price":89.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/JH-9mm-Aluminium-External-Square-Corner.png?v=1766107886"},{"product_id":"james-hardie-aluminium-internal-corner-3m","title":"James Hardie 14mm aluminium internal corner 3000mm","description":"\u003cp\u003eThis is the James Hardie 14mm aluminium internal corner, a 3000 mm long aluminium extrusion that forms the internal corners on walls clad in Stria Cladding. It is supplied ready to paint.\u003c\/p\u003e\u003ch2\u003eKey facts\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLength: 3000 mm\u003c\/li\u003e\n\u003cli\u003eSize: 14 mm\u003c\/li\u003e\n\u003cli\u003eMaterial: aluminium extrusion\u003c\/li\u003e\n\u003cli\u003eFinish: ready to paint\u003c\/li\u003e\n\u003cli\u003eMade for: James Hardie Stria Cladding, internal corners\u003c\/li\u003e\n\u003cli\u003eWeight: about 1.35 kg per length\u003c\/li\u003e\n\u003cli\u003eJames Hardie product code: 305518\u003c\/li\u003e\n\u003cli\u003eSold as: single 3000 mm length\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\u003cp\u003eIt goes into the inside corner where two Stria-clad walls meet, so the boards finish against a straight aluminium line. Internal corner here means an inside corner of a clad wall. It is not a trim for plasterboard or other interior linings. James Hardie lists it for Stria Cladding.\u003c\/p\u003e\u003ch2\u003eInstallation\u003c\/h2\u003e\u003cp\u003eJames Hardie's Stria Cladding installation guides, horizontal and vertical, show the internal corner detail. In short: fix the aluminium corner with 40 mm fibre cement nails at 300 mm vertical centres through both flanges, then install the boards leaving a nominal 2 mm gap to the aluminium corner. The guides also call for a continuous bead of Hardie Joint Sealant at the corner flashing. Follow the current guide for the full detail and the order of work, and paint the corner with the wall.\u003c\/p\u003e\u003ch2\u003eCommon questions\u003c\/h2\u003e\u003ch3\u003eWhich cladding does this corner suit?\u003c\/h3\u003e\u003cp\u003eJames Hardie lists it for Stria Cladding. James Hardie also makes a 9mm aluminium internal corner, so ask us which one your cladding needs.\u003c\/p\u003e\u003ch3\u003eHow many do I need?\u003c\/h3\u003e\u003cp\u003eMultiply the wall height by the number of internal corners and divide by 3000 mm. Round up to whole lengths.\u003c\/p\u003e\u003ch3\u003eDoes it come painted?\u003c\/h3\u003e\u003cp\u003eNo. It is supplied ready to paint and is painted on site.\u003c\/p\u003e\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\u003cp\u003eYes. Pick up from our store at 10 Lancaster Street, Ingleburn, or have it delivered across Sydney. Call (02) 4605 0215 for a delivery quote. At 3.0 m long it needs racks, a tray or a trailer.\u003c\/p\u003e","brand":"James Hardie","offers":[{"title":"Default Title","offer_id":47748419715383,"sku":"305518","price":76.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/JH-Alu-Int-Corner-3m.png?v=1766105868"},{"product_id":"paslode-impulse-cladfast-50mm-ag-hp-pk1000","title":"Paslode Impulse CladFast cladding nails 50mm AG, handy pack 1000","description":"\u003cp\u003ePaslode Impulse CladFast 50 mm AG nails in a handy pack of 1000, Paslode part number B20548. CladFast is Paslode's round offset head nail, used for gas nailing cladding and weatherboards to timber frames.\u003c\/p\u003e\n\u003ch2\u003eKey facts\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eBrand: Paslode, part number B20548\u003c\/li\u003e\n\u003cli\u003eNail length: 50 mm\u003c\/li\u003e\n\u003cli\u003eHead: CladFast round offset head\u003c\/li\u003e\n\u003cli\u003eFinish: AG, as marked on the box\u003c\/li\u003e\n\u003cli\u003ePack: 1000 nails (Impulse Handy Pack)\u003c\/li\u003e\n\u003cli\u003eWeight: about 2.5 kg per box\u003c\/li\u003e\n\u003cli\u003eSuits: Paslode Impulse gas nailers\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\n\u003cp\u003eFixing cladding boards, weatherboards and similar exterior linings to timber framing with a Paslode Impulse nailer. Paslode says the round offset head gives better holding and a neater look.\u003c\/p\u003e\n\u003ch2\u003eWorking with it\u003c\/h2\u003e\n\u003cp\u003eCheck the cladding maker's fixing guide first. It sets the nail type, length, finish, spacing and edge distances, and some claddings do not allow gun nails. Check your nailer's manual for the nail lengths and head types it takes. Set the depth so the heads finish flush with the board, not punched below the surface. Keep nails and fuel cells dry and out of the heat.\u003c\/p\u003e\n\u003ch2\u003eCommon questions\u003c\/h2\u003e\n\u003ch3\u003eWhat does AG mean on the box?\u003c\/h3\u003e\n\u003cp\u003eAG is the finish marked on this box. Paslode's nail guide describes an Armor Galv finish for exterior work where a hot dipped or mechanically galvanised nail is specified, but it does not list this part number, so we have not confirmed the coating. Call us before using these on a coastal or severe exposure job.\u003c\/p\u003e\n\u003ch3\u003eDoes the box include gas?\u003c\/h3\u003e\n\u003cp\u003ePaslode Impulse handy packs normally hold 1000 nails with one fuel cell. Paslode's website does not list this part number, so check the box or call us to confirm.\u003c\/p\u003e\n\u003ch3\u003eWill they fit my nailer?\u003c\/h3\u003e\n\u003cp\u003eThey are Paslode Impulse strip nails. Check your tool's manual for CladFast nails in 50 mm before you buy, or call us with the tool model.\u003c\/p\u003e\n\u003ch3\u003eCan I pick them up or get them delivered?\u003c\/h3\u003e\n\u003cp\u003eYes. Pick up from our store at 10 Lancaster Street, Ingleburn, or add them to a delivery anywhere in Sydney. Call (02) 4605 0215 to check stock.\u003c\/p\u003e","brand":"Paslode","offers":[{"title":"Default Title","offer_id":47748387930423,"sku":"B20548","price":99.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/Impulse-cladfast-50mm-HP.png?v=1754676065"},{"product_id":"paslode-45x2-5mm-coil-ring-nails-for-cladding","title":"Paslode Impulse coil nails 45 x 2.5mm ring shank, HDG, box 2400","description":"\u003cp\u003ePaslode Impulse coil nails, 45 x 2.5 mm, with a ring shank and a hot dipped galvanised finish, in a box of 2400 (Paslode part number B40021). They are made for the Paslode Impulse CoilMaster nailer and are used for gun nailing fibre cement cladding to timber frames.\u003c\/p\u003e\u003ch2\u003eKey facts\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eBrand: Paslode, part number B40021\u003c\/li\u003e\n\u003cli\u003eNail size: 45 x 2.5 mm\u003c\/li\u003e\n\u003cli\u003eShank: ring\u003c\/li\u003e\n\u003cli\u003eFinish: hot dipped galvanised\u003c\/li\u003e\n\u003cli\u003eBox: 2400 nails\u003c\/li\u003e\n\u003cli\u003eSuits: Paslode Impulse CoilMaster\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\u003cp\u003eGun nailing fibre cement cladding and weatherboards to timber wall frames. James Hardie's Linea Weatherboard installation guide lists a Paslode 45 x 2.5 mm ring shank coil nail for concealed nailing to timber frames, and Paslode's fixing matrix for James Hardie products names this nail by part number. The matrix and Paslode's CoilMaster fixing guide are attached to this page. We stock \u003ca href=\"\/products\/scyon-linea-4200x180x16mm\"\u003eLinea Weatherboard 180 mm\u003c\/a\u003e and \u003ca href=\"\/products\/james-hardie-linea-cladding\"\u003eLinea Weatherboard 150 mm\u003c\/a\u003e. For brackets and bracing, see the \u003ca href=\"\/products\/paslode-32x2-5mm-sheg-coil-nails-for-bracing-2400-nails\"\u003e32 x 2.5 mm screw shank coil nails\u003c\/a\u003e.\u003c\/p\u003e\u003ch2\u003eWorking with it\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eCheck the James Hardie installation guide for the cladding you are fixing. It sets the nail, the spacing and where each nail goes.\u003c\/li\u003e\n\u003cli\u003ePaslode's guide says not to overdrive nails in fibre cement board, and to use a no-mar tip to avoid marking the surface.\u003c\/li\u003e\n\u003cli\u003ePaslode says to check your local wind rating when you choose a fastener.\u003c\/li\u003e\n\u003cli\u003eThis nail is hot dipped galvanised. Paslode's guide lists stainless steel nails for coastal zones, and James Hardie's Linea guide calls for class 4 fasteners within 1 km of the coast. Check your specification before you use galvanised nails near the sea.\u003c\/li\u003e\n\u003cli\u003eCheck your nailer's manual for the nail sizes it takes. Keep nails and fuel cells dry and out of the heat.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eCommon questions\u003c\/h2\u003e\u003ch3\u003eWhat size is the nail and how many are in a box?\u003c\/h3\u003e\u003cp\u003ePaslode lists part number B40021 as 45 mm long and 2.5 mm in diameter, with a ring shank and a hot dipped galvanised finish, 2400 nails to a box.\u003c\/p\u003e\u003ch3\u003eDoes the box include gas?\u003c\/h3\u003e\u003cp\u003ePaslode lists this nail with its Impulse value packs, but its table does not say how many fuel cells are in the box. Check the box or call us to confirm.\u003c\/p\u003e\u003ch3\u003eWill they fit my nailer?\u003c\/h3\u003e\u003cp\u003ePaslode lists them as compatible with the Impulse CoilMaster. Check the part number against your tool's manual before you buy.\u003c\/p\u003e\u003ch3\u003eCan I pick them up or get them delivered?\u003c\/h3\u003e\u003cp\u003eYes. Pick up from our store at 10 Lancaster Street, Ingleburn, or add them to a delivery anywhere in Sydney. Call (02) 4605 0215 to check stock.\u003c\/p\u003e","brand":"Paslode","offers":[{"title":"Default Title","offer_id":47748387701047,"sku":"B40021","price":147.46,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/COIL-NAILS-45.png?v=1754676063"},{"product_id":"hume-4200-x-230-primaplank-7-5mm-smooth","title":"PrimaPlank smooth fibre cement weatherboard plank 4200 x 230 x 7.5mm","description":"\u003cp\u003ePrimaPlank Smooth is a 7.5 mm fibre cement cladding plank, 4200 mm long and 230 mm wide, with a smooth face. The planks are fixed in overlapping rows, like weatherboards, to clad walls and gable ends.\u003c\/p\u003e\u003ch2\u003eKey facts\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSize: 4200 x 230 x 7.5 mm\u003c\/li\u003e\n\u003cli\u003eFinish: smooth face\u003c\/li\u003e\n\u003cli\u003eMaterial: fibre cement. The maker of PRIMA Plank, Saint-Gobain Prima, describes it as an autoclaved cellulose fibre reinforced cement board, made from Portland cement, cellulose fibre, ground sand and water\u003c\/li\u003e\n\u003cli\u003eFace area: about 0.97 m² per plank, before the lap\u003c\/li\u003e\n\u003cli\u003eWeight: about 9 kg per plank\u003c\/li\u003e\n\u003cli\u003eSold as: single plank\u003c\/li\u003e\n\u003cli\u003ePrimed or unprimed, lap and fixing details: not listed online yet. Call us on (02) 4605 0215\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\u003cp\u003eWeatherboard-style cladding on walls and gable ends. The smooth face gives a plain painted weatherboard look. We also stock \u003ca href=\"\/products\/bgc-joiners-smooth-230mm-pk-25\"\u003e230 mm smooth plank joiners\u003c\/a\u003e and \u003ca href=\"\/products\/bgc-pvc-joiners-primaplank-300mm\"\u003ePVC joiners for PrimaPlank\u003c\/a\u003e. Call us to check which joiner suits this plank before you order.\u003c\/p\u003e\u003ch2\u003eInstallation\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFollow the maker's installation guide for the lap, stud spacing, fixings, joints and clearances. It is not online here yet, so ask us for it.\u003c\/li\u003e\n\u003cli\u003eExternal cladding goes over wall wrap and flashings, as your plans and the building code require.\u003c\/li\u003e\n\u003cli\u003eCutting fibre cement makes silica dust. Cut outdoors with a score and snap knife, fibre cement shears or a saw with dust extraction, and wear a P2 mask.\u003c\/li\u003e\n\u003cli\u003eCarry planks on edge. Store them flat, dry, off the ground and under cover.\u003c\/li\u003e\n\u003cli\u003eFibre cement cladding is a painted finish. Check the maker's guide for priming and paint before you start.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eCommon questions\u003c\/h2\u003e\u003ch3\u003eHow many planks do I need?\u003c\/h3\u003e\u003cp\u003eIt depends on the lap. Take the lap in the maker's guide off the 230 mm width to get the cover per row. Divide the wall height by that cover for the number of rows, then divide the wall length by 4.2 m for the planks per row. Add 5 to 10 per cent for cuts.\u003c\/p\u003e\u003ch3\u003eHow heavy is a plank?\u003c\/h3\u003e\u003cp\u003eAbout 9 kg. A 4.2 m plank is long and flexible, so carry it on edge, with two people if you can.\u003c\/p\u003e\u003ch3\u003eIs it pre-primed?\u003c\/h3\u003e\u003cp\u003eThat is not listed online yet. Call (02) 4605 0215 and we will check the pack for you.\u003c\/p\u003e\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\u003cp\u003eYes. Pick up from our store at 10 Lancaster Street, Ingleburn, or have it delivered across Sydney. The planks are 4.2 m long, so bring a ute with racks or a truck, or call for a delivery quote.\u003c\/p\u003e","brand":"Alpha Timber","offers":[{"title":"Default Title","offer_id":47748373578039,"sku":"24472","price":28.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/Primaplank-Smooth-4200x230x7.5mm.png?v=1766026127"},{"product_id":"scyon-linea-4200x180x16mm","title":"James Hardie Linea Weatherboard 16mm, 4200 x 180mm fibre cement","description":"\u003cp\u003eLinea Weatherboard is James Hardie's 16 mm thick fibre cement weatherboard, sold here as a 4200 x 180 mm board. The pre-primed boards are lapped and fixed across timber or light steel wall frames as external cladding with deep shadow lines, then painted. It was sold before as Scyon Linea.\u003c\/p\u003e\u003ch2\u003eKey facts\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eThickness: 16 mm\u003c\/li\u003e\n\u003cli\u003eBoard size: 4200 x 180 mm (4205 mm overall with the tongue and groove end)\u003c\/li\u003e\n\u003cli\u003eMaterial: fibre cement, pre-primed\u003c\/li\u003e\n\u003cli\u003eEnds: tongue and groove short ends, so boards can join off the stud\u003c\/li\u003e\n\u003cli\u003eWeight: about 3.4 kg per metre, so about 14 kg per board (James Hardie's guide)\u003c\/li\u003e\n\u003cli\u003eCover: at the 30 mm lap, 150 mm per row, about 0.63 m² per board\u003c\/li\u003e\n\u003cli\u003eJames Hardie product code: 403912\u003c\/li\u003e\n\u003cli\u003eSold as: single boards\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\u003cp\u003eExternal wall cladding with a wide weatherboard look. James Hardie's guide covers residential walls over a seasoned timber frame or a light gauge steel frame. For the narrower board, see \u003ca href=\"\/products\/james-hardie-linea-cladding\"\u003eLinea Weatherboard 150 mm\u003c\/a\u003e. For corners, see the \u003ca href=\"\/products\/james-hardie-scyon-linea-aluminium-external-slimline-boxed-corner-3-6m\"\u003eLinea external slimline boxed corner\u003c\/a\u003e and the \u003ca href=\"\/products\/james-hardie-scyon-linea-16mm-aluminium-internal-corner-mould-3-6m\"\u003eLinea internal corner mould\u003c\/a\u003e.\u003c\/p\u003e\u003ch2\u003eInstallation\u003c\/h2\u003e\u003cp\u003eThese points come from James Hardie's Linea Weatherboard installation guide (September 2026), attached to this page.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eStud spacing depends on the wind class. It is 600 mm maximum up to N3\/C1, and closer near building edges and in higher wind classes. Check Table 3 of the guide for your site.\u003c\/li\u003e\n\u003cli\u003eLap each board 30 mm over the one below.\u003c\/li\u003e\n\u003cli\u003eTimber frames: face nail with 60 x 3.15 mm bullet head nails, or conceal nail with 40 x 2.8 mm fibre cement nails or Paslode 45 x 2.5 mm ring shank coil nails. Steel frames: 41 mm Hardie Drive screws.\u003c\/li\u003e\n\u003cli\u003eWithin 1 km of the coast, James Hardie calls for class 4 fasteners.\u003c\/li\u003e\n\u003cli\u003eEnd joints are tongue and groove and sit off the stud, at least 100 mm from the side of a stud. Run a continuous bead of Hardie Joint Sealant on the back of the tongue and push the boards firmly together. Keep joints in adjacent rows at least one stud spacing apart.\u003c\/li\u003e\n\u003cli\u003eKeep at least 150 mm clearance to the ground and 50 mm to roofs, decks, paths, steps and driveways.\u003c\/li\u003e\n\u003cli\u003ePaint within 3 months of fixing, or within 7 days if the site is within 1 km of the coast. James Hardie recommends at least two coats of quality exterior acrylic paint.\u003c\/li\u003e\n\u003cli\u003eFibre cement dust contains silica. Cut outdoors with a hand guillotine, fibreshear or a dust-reducing saw with an M class vacuum. Wear a P2 respirator, and never use a grinder or dry sweep the dust.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eFollow the current James Hardie guide for the full detail. For bracing, fire rated walls or anything structural, check with your building designer or engineer.\u003c\/p\u003e\u003ch2\u003eCommon questions\u003c\/h2\u003e\u003ch3\u003eHow many boards do I need?\u003c\/h3\u003e\u003cp\u003eAt the 30 mm lap each row covers 150 mm, so you need about 6.7 rows for every metre of wall height. One 4200 mm board covers about 0.63 m². Divide your wall area by that figure and add an allowance for offcuts around windows and doors.\u003c\/p\u003e\u003ch3\u003eDo the end joints have to land on a stud?\u003c\/h3\u003e\u003cp\u003eNo. The short ends are tongue and groove and are joined off the stud, at least 100 mm from the side of a stud, with sealant on the back of the tongue.\u003c\/p\u003e\u003ch3\u003eDoes Linea need painting?\u003c\/h3\u003e\u003cp\u003eYes. The boards are pre-primed and must be painted within 3 months of being installed, or within 7 days near the coast.\u003c\/p\u003e\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\u003cp\u003eYes. Pick up from our store at 10 Lancaster Street, Ingleburn, or ask us about delivery across Sydney. Call (02) 4605 0215 to check stock. The boards are 4.2 m long, so bring racks, a long tray or a trailer.\u003c\/p\u003e","brand":"James Hardie","offers":[{"title":"Default Title","offer_id":47796294353207,"sku":"403912","price":55.77,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/Scyon-Linea-4200x180x16mm.jpg?v=1766391907"},{"product_id":"james-hardie-joint-sealent-grey-300ml-cartridge-20-box","title":"James Hardie joint sealant 300ml cartridge, exterior polyurethane","description":"\u003cp\u003eHardie Joint Sealant is a general purpose, paintable, exterior grade polyurethane joint sealant by James Hardie, in a 300 ml cartridge (product code 305534). It seals the joints, corners and gaps when Hardie fibre cement cladding and trims are installed.\u003c\/p\u003e\u003ch2\u003eKey facts\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eBrand: James Hardie, product code 305534\u003c\/li\u003e\n\u003cli\u003eType: polyurethane joint sealant, exterior grade, general purpose\u003c\/li\u003e\n\u003cli\u003eSize: 300 ml cartridge\u003c\/li\u003e\n\u003cli\u003ePaintable: yes. James Hardie lists it as ready to paint after installation\u003c\/li\u003e\n\u003cli\u003eColour: listed in our stock system as white. Call us to confirm before you order\u003c\/li\u003e\n\u003cli\u003eWeight: about 0.45 kg per cartridge\u003c\/li\u003e\n\u003cli\u003eBox quantity: our stock system lists 20 cartridges to a box. Call to confirm whether you are ordering single cartridges or a box\u003c\/li\u003e\n\u003cli\u003eJames Hardie does not recommend it for fire applications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\u003cp\u003eJames Hardie calls it an essential item when installing any Hardie fibre cement product, and says it works as a joint sealant and as a construction adhesive. James Hardie's installation guides call for it at points such as these:\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eA continuous bead in aluminium corner accessories before the cladding panels slide in.\u003c\/li\u003e\n\u003cli\u003eA continuous bead on the back of the tongue at the end joins of Linea Weatherboard.\u003c\/li\u003e\n\u003cli\u003eGaps of up to 2 mm where Axent Trim meets the cladding.\u003c\/li\u003e\n\u003cli\u003eBetween a horizontal h flashing and its jointer.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThe installation guide for each cladding shows exactly where the sealant goes. You will find it in the Certificates \u0026amp; Brochures section on our page for that cladding.\u003c\/p\u003e\u003ch2\u003eWorking with it\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eApply to clean, dry, dust free surfaces.\u003c\/li\u003e\n\u003cli\u003eCut the nozzle to suit the bead size in the installation guide and run a continuous bead with no breaks.\u003c\/li\u003e\n\u003cli\u003eTool the bead before it skins. Skin and cure times are printed on the cartridge.\u003c\/li\u003e\n\u003cli\u003eLet the sealant cure before painting, and paint the wall within the time the cladding guide gives.\u003c\/li\u003e\n\u003cli\u003eDo not use it in a joint that needs a fire rated sealant.\u003c\/li\u003e\n\u003cli\u003eStore cartridges cool and dry, and check the use by date before you start.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eFor more details, call us on \u003ca href=\"tel:0246050215\"\u003e(02) 4605 0215\u003c\/a\u003e and we will help you.\u003c\/p\u003e\u003ch2\u003eCommon questions\u003c\/h2\u003e\u003ch3\u003eCan it be painted?\u003c\/h3\u003e\u003cp\u003eYes. James Hardie describes it as a paintable sealant that is ready to paint after installation.\u003c\/p\u003e\u003ch3\u003eHow far does a cartridge go?\u003c\/h3\u003e\u003cp\u003eIt depends on the bead size. By volume, 300 ml is about 15 lineal metres of a 5 mm round bead, and less for a bigger bead. Allow for waste.\u003c\/p\u003e\u003ch3\u003eIs the price for one cartridge or a box?\u003c\/h3\u003e\u003cp\u003eOur stock system lists 20 cartridges to a box. Call (02) 4605 0215 before you order so we can confirm the pack and the colour.\u003c\/p\u003e\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\u003cp\u003eYes. Pick up from our store at 10 Lancaster Street, Ingleburn, or add it to a cladding delivery anywhere in Sydney.\u003c\/p\u003e","brand":"James Hardie","offers":[{"title":"Default Title","offer_id":47796299825463,"sku":"305534","price":25.99,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/products\/James-Hardie-joint-Sealent-White-300ml-Cartridge-20_Box.png?v=1766109630"},{"product_id":"ezygroove-fibre-cement-panel-1200-mm-9-mm","title":"EZYGroove fibre cement cladding panel 9mm, 2450 or 3000 x 1200mm","description":"\u003cp\u003eEZYGroove is a 9 mm fibre cement cladding panel, 1200 mm wide, with grooves formed in the face. It comes in 2450 mm and 3000 mm sheets and gives walls a grooved, jointed panel look once painted.\u003c\/p\u003e\n\u003ch2\u003eKey facts\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eSheet sizes: 2450 x 1200 mm and 3000 x 1200 mm\u003c\/li\u003e\n\u003cli\u003eThickness: 9 mm\u003c\/li\u003e\n\u003cli\u003eMaterial: fibre cement\u003c\/li\u003e\n\u003cli\u003eFace: pre-grooved, smooth and ready to paint\u003c\/li\u003e\n\u003cli\u003eCoverage: 2.94 m² per 2450 mm sheet, 3.6 m² per 3000 mm sheet\u003c\/li\u003e\n\u003cli\u003eWeight: about 42 kg (2450 mm sheet) and 52 kg (3000 mm sheet), about 14.4 kg per m²\u003c\/li\u003e\n\u003cli\u003eSold as: single sheet\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eWhat it is used for\u003c\/h2\u003e\n\u003cp\u003eExternal wall cladding and internal feature walls on houses and light commercial buildings, where you want defined groove lines instead of a flat sheet. The panel is painted on site in your own colour.\u003c\/p\u003e\n\u003ch2\u003eWorking with it\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eFollow the manufacturer's installation guide for framing, fixings, joints and flashings. Ask us for it when you order.\u003c\/li\u003e\n\u003cli\u003eFibre cement dust contains silica. Cut outdoors with score and snap tools, fibre cement shears or a dust-reducing saw with extraction, and wear a P2 mask.\u003c\/li\u003e\n\u003cli\u003eCarry sheets on edge with two people. A 3000 mm sheet is about 52 kg.\u003c\/li\u003e\n\u003cli\u003eStore sheets flat, dry and off the ground until they are fixed.\u003c\/li\u003e\n\u003cli\u003eSeal cut edges and paint the wall as the paint maker directs.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eCommon questions\u003c\/h2\u003e\n\u003ch3\u003eHow many sheets do I need?\u003c\/h3\u003e\n\u003cp\u003eA 2450 mm sheet covers 2.94 m² and a 3000 mm sheet covers 3.6 m². A 10 m² wall needs four 2450 mm sheets or three 3000 mm sheets before waste. Add about 10% for cuts and openings.\u003c\/p\u003e\n\u003ch3\u003eHow heavy is a sheet?\u003c\/h3\u003e\n\u003cp\u003eAbout 42 kg for a 2450 mm sheet and 52 kg for a 3000 mm sheet. Plan on two people to lift and fix each sheet.\u003c\/p\u003e\n\u003ch3\u003eDoes it need painting?\u003c\/h3\u003e\n\u003cp\u003eYes. The face is smooth and ready to paint. Paint it after installation with an exterior paint if it is on an outside wall.\u003c\/p\u003e\n\u003ch3\u003eCan I pick it up or get it delivered?\u003c\/h3\u003e\n\u003cp\u003eYes. Pick up from our store at 10 Lancaster Street, Ingleburn, or have it delivered across Sydney. Sheets travel flat, so check your ute or trailer can take a 3000 x 1200 mm sheet. Call (02) 4605 0215 to check stock.\u003c\/p\u003e","brand":"ALPHA TIMBER","offers":[{"title":"2450m","offer_id":51600704831799,"sku":"EZY0001","price":109.0,"currency_code":"AUD","in_stock":true},{"title":"3000m","offer_id":51600704897335,"sku":"EZY0003","price":125.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/9754\/6039\/files\/EzyGroove-1200-9mm.png?v=1769052048"}],"url":"https:\/\/alphatimber.com.au\/collections\/cladding-project.oembed","provider":"ALPHA TIMBER","version":"1.0","type":"link"}